How to replace the battery

Please follow the instructions in the video.

Gurgling noise

A gurgling noise can be caused by two different issues.

Out of the box

This can usually be resolved by running approximately 2 to 4 tanks of water through the machine when in Humidifier mode.

Paper in the clear bin

This will indicate that the machine is working correctly.

Like our other cordless vacuums, this machine is engineered for quick clean-ups on hard floors and carpeting, as well as for furniture, stairs and inside the car.

Machine settling

This may be caused by the machine settling and will pass with time.

No fault with the machine

There is no fault with the machine, the noise can sometimes be heard when the ultrasonic transducer produces mist inside the base of your machine.

This noise is most noticeable when the machine is new, but the noise will reduce in volume once approximately 3-4 full tanks of water have been run through the machine.

Airspeed control

Please ensure the correct button is being pressed.

On/Off

Airspeed control

Test the remote control

Please ensure the correct button is being pressed.

On/Off

Fan only mode

Airspeed control

Manual humidity level control

Sleep timer

Automatic humidity mode

Replace the batteries

Replace the batteries in the remote control.

F1

An F1 message indicates an issue with the Piezo.

Turn off & unplug the machine, leave it for 60 seconds and then retest.

This process may need to be repeated up to 3 times.

F2

An F2 message indicates an issue with the UV-C emitter.

Turn off & unplug the machine, leave it for 60 seconds and then retest.

This process may need to be repeated up to 3 times.

F3

A F3 failure message means the appliance is too cold.

The appliance will operate when it is above 5°C (41°F).

If your machine displays an error code F3, please turn the power off and unplug the machine for 60 seconds.

Increase room temperature to 5°C or above before restarting machine.

Plug the machine back in and retest.

Please repeat this process up to 3 times if your machine continues to display an error code.

F4

Turn off & unplug the machine, leave it for 60 seconds and then retest.

This process may need to be repeated up to 3 times.

F5

Turn off & unplug the machine, leave it for 60 seconds and then retest.

This process may need to be repeated up to 3 times.

Humidifier mode

Adjust the humidity control to 70%.

Adjust the airflow to the lowest setting.

It is easier to see the mist when the machine is in front of a dark background.

If no mist is visible then clear the amplifier of any obstructions.

If the machine is in automatic mode then it may shut off

The appliance selects a comfortable humidity for the room, based on environmental factors such as current humidity level and air temperature.

When the room reaches the appropriate humidity level the appliance will switch itself ‘ON’ or ‘OFF’ as necessary to maintain that level. The fan will remain running when the target humidity has been reached.

Clear the loop amplifier

Remove the loop amplifier and press the button at the front of the loop.

Lift the loop off the machine and pull the amp surround off the loop, one end at a time.

Check the seal is fitted and seated correctly.

Wipe both parts with a damp cloth.

WARNING: Do not clean any part in a dishwasher.

Reattach the surround and line up the surround with the amp.

Push the surround firmly until it clicks into place.

Turn on and test the machine.

Airflow

Switch off the humidity and set the fan speed to 10.

You will see the fan speed changing on the digital display.

Clean the machine

Clean the loop amplifier with a microfibre, lint-free cloth.

Ensure there is no dust or debris blocking the openings.

Clear any dust or debris away from the inlet vents at the base of the machine.

Clear the amplifier

Press the button at the front of the loop amplifier.

Lift the amplifier from the machine.

Pull the amp surround off the loop, one end at a time.

Clear the loop amplifier and surround of blockages as necessary.

Weekly maintenance

Please follow the steps in the video.

For a step by step guide, please select step by step.

Weekly maintenance

Wipe the loop and inlets:

Wipe over air loop amplifier, paying close attention to the air gaps.

Wipe with a lint-free microfibre cloth.

Clean the tank

Empty the water tank.

Rinse and wipe over all surfaces.

Repeat if necessary.

Empty the trough

Tip the contents of the trough into the sink

Wipe away any spillages

Clean the base

WARNING: Do not rinse under the tap or put in the dishwasher.

While not dangerous, care should be taken to avoid water entering the inlets.

Wipe the exterior with a lint free microfibre cloth.

Check the machine

If the power button flashes 3 times when switching on check that the machine has been assembled correctly.

Check that the tank is sat flush onto the Main body, when fitting the loop amplifier make sure that it clicks into place securely.

Quick start guide

Ensure the base is on a level surface, otherwise the machine will not operate.

Unscrew the cap and fill the tank to the top.

Replace the cap and screw until hand tight.

Carry by the handle.

Place the tank on top of the base.

Step 2

Place the loop amplifier on top of the tank.

Push down until you hear a click.

Remote control docks magnetically.

Attach the remote control to the top of the machine with the buttons facing down.

Step 3

Plug into the socket and base.

A small blue LED on the back of the machine lights up to confirm that the machine has power.

Step 4

Switch ‘ON’.

The water treatment procedure automatically starts.

Water passes over a UV-C emitter to ensure that it is 99.9% bacteria-free before misting commences.

This takes approximately 3 minutes.

During this time humidity targets can be set and fan mode can be switched ON.

After 3 minutes the machine will start to humidify.

The display will show the target humidity setting.

Check the electrics

Ensure the machine is plugged in and the socket is switched on.

On the rear of the machine, just beneath where the power cord plugs in is a power indicator light that should illuminate when the machine is plugged in.

Press the ON/OFF button again to start the machine.

If the machine cuts out or will not switch on, please turn it off at the socket and remove the plug.

Wait 10 seconds, plug the machine back in and ensure the socket is switched on.

Press the ON/OFF button again to start the machine.

Test socket

Please try another socket.

Is the machine tilted?

The machine will not operate if tilted by over 5 degrees and the display will show a 'tilted' graphic.

The blue LED surrounding the Standby ON/OFF button will flash if the base is not level.

Make sure it is on a level surface and clear up any spillage.

The machine will cut out when the humidity target is reached.

Check the tank

The machine will cut out if the tank is empty.

The blue LED surrounding the Standby ON/OFF button will remain solid as the water level changes.

When the tank is empty, an animation sequence appears.

If the tank is empty, switch off the machine and refill.

Ensure the tank is full.

Refill the tank

Turn the machine off.

Unplug the appliance and push the button to unlock.

Lift the loop amplifier away from the tank.

Lift the tank away from the base.

Remove the cap and fill the tank (no other part) to the top with cold tap water.

Replace the cap.

Replace the tank and ensure it is fitted flush.

When replacing the loop ensure it 'clicks' into place securely.

Use the handle for easier handling.

Please be aware that water drips may be present on the underside of the tank when removed. If the power button on the machine flashes three times this may indicate that the machine has been reassembled incorrectly.

Water treatment procedure

While the AM10 is in humidifier mode, it constantly treats the water it emits, keeping it hygienic.

When the machine is first switched on, it will begin this water treatment procedure, displaying this animation on the LCD.

After 3 minutes the machine will begin to humidify the room.

Weekly maintenance

Weekly maintenance

Wipe the loop and inlets:

Wipe over air loop amplifier, paying close attention to the air gaps.

Wipe with a lint-free microfibre cloth.

Clean the tank

Empty the water tank.

Rinse and wipe over all surfaces.

Repeat if necessary.

Empty the trough

Tip the contents of the trough into the sink

Wipe away any spillages

Clean the base

WARNING: Do not rinse under the tap or put in the dishwasher.

While not dangerous, care should be taken to avoid water entering the inlets.

Wipe the exterior with a lint free microfibre cloth.

Monthly maintenance

Unclip the loop amplifier surround

Pull from the lower edge by hand, gently but firmly.

Wipe with citric acid solution.

Clean the chimney

Empty the tank

Twist the dial a quarter of a turn and lift out the chimney.

Immerse in the citric acid solution for 15 minutes.

Rinse and wipe all parts and refit the chimney.

Clean the seal

Pinch the tabs together and remove the seal

Immerse in the citric acid solution for 15 minutes

Rinse and wipe all parts and refit the seal.

Clean the tank

Pour the citric acid solution into the tank

Shake for 30 seconds and leave to stand

After 15 minutes, empty the tank and wipe all surfaces

Clean the base

Empty the trough of water

While not dangerous, care should be taken to avoid water entering the inlets.

Clean the trough with the citric acid solution.

Fill the trough with the solution so that the UV-C emitter and piezo are submerged.

After 15 minutes, rinse and wipe over all surfaces.

Reassemble the machine

Reassemble and re-fill the machine then wipe the exterior with a dry lint-free cloth

Switch the machine on to start the water treatment procedure

After 3 minutes the machine will start to humidify

Remove the tank

Remove the tank from the Main body.

With the tank removed, fit the loop amplifier onto the Main body.

Water in the tank

The AM10 will display the 'Empty' light sequence when there is still a small amount of water in the tank.

Empty the tank

Empty the tank and turn it upside down.

Float not moving freely

The float may not be moving as freely as it should because of the build-up of minerals from the water. Clean the tank according to the monthly maintenance instructions.

Pour the citric acid solution into the tank.

Shake for 30 seconds and leave to stand.

After 15 minutes, empty the tank and wipe all surfaces.

Reassemble and test the machine.

ON/OFF button

3 flashes - Check that the machine has been assembled correctly

Solid blue - The machine is running in humidity mode

Solid white - The machine is running in fan mode

Water treatment procedure

When the machine is switched on, a 3 minute water treatment cycle begins

The blue LED surrounding the Standby ON/OFF button will remain solid throughout the water treatment cycle.

Once the animation stops, the machine is ready to begin humidification

Water level

The blue LED surrounding the Standby ON/OFF button will remain solid as the water level changes

When the tank is empty the LCD will display the animation shown

If the tank is empty, switch ‘OFF’ the machine and refill

Tilt indicator

The blue LED surrounding the Standby ON/OFF button will flash if the base is not level

When the machine is tilted by over 5° the display will show a ‘tilted’ graphic

If the machine has been tilted make sure it is level and clear up any spillage

Check loop

Ensure the coloured loop surround is located properly on the amp and the seal is in the correct position.

Remove the loop surround and run the finger along the inner lip surface to ensure it touches the seal.

Reattach and ensure it is centrally located and reset the machine.

Check loop

This can be caused by the loop not being fitted correctly, ensure the tank is fitted flush and the loop clicks into place securely.

If the mist is coming from the joint between the base and the tank, the machine may be slightly tilted.

Check that the machine is on a completely level surface.

If the machine is tilted, the blue LED surrounding the Standby ON/OFF button will flash if the base is not level.

When the machine is tilted by over 5° the display will show a 'tilted' graphic.

If the machine has been tilted ensure it is level and to clear up any spillage. If the machine is not levelled after 15 minutes, it will switch 'OFF'.

Check inner chimney and seals

Check that the inner chimney is located correctly and the seals are located in the correct location.

Ensure that the product is on a level surface.

Clear the loop amplifier

Ensure the machine is in humidifier mode, if no mist is visible then clear the amplifier of any obstructions.

Remove the loop amplifier

Press the button at the front of the Loop

Lift the Loop off the machine

Pull the amp surround off the loop, one end at a time.

Check the seal is fitted and seated correctly.

Wipe both parts with a damp cloth

WARNING: Do not clean any part in the dishwasher.

Reattach the surround

Line up the surround with the amp

Push the surround firmly until it clicks into place

Turn on and test the machine

Adjust the humidity control to 70%.

Adjust the airflow to the lowest setting.

It is easier to see the mist when the machine is in front of a dark background.

If this fault persists remove the loop and ensure that the seal is free to move up and down before re-engaging. Sealing can be aided by applying a thin film of water over the seal.

No fault with machine

There is no fault with the machine; this powder is limescale from the water put into the tank.

To prevent its formation, use de-ionised or distilled water (particularly in hard water areas) & follow the weekly & monthly cleaning processes.

Monthly maintenance

Unclip the loop amplifier surround

Pull from the lower edge by hand, gently but firmly

Wipe with citric acid solution.

Clean the chimney

Empty the tank

Twist the dial a quarter of a turn and lift out the chimney.

Immerse in the citric acid solution for 15 minutes.

Rinse and wipe all parts and refit the chimney.

Clean the seal

Pinch the tabs together and remove the seal

Immerse in the citric acid solution for 15 minutes

Rinse and wipe all parts and refit the seal.

Clean the tank

Pour the citric acid solution into the tank

Shake for 30 seconds and leave to stand

After 15 minutes, empty the tank and wipe all surfaces

Clean the base

Empty the trough of water

While not dangerous, care should be taken to avoid water entering the inlets.

Clean the trough with the citric acid solution.

Fill the trough with the solution so that the UV-C emitter and piezo are submerged.

After 15 minutes, rinse and wipe over all surfaces.

Reassemble the machine

Reassemble and re-fill the machine then wipe the exterior with a dry lint-free cloth

Switch the machine on to start the water treatment procedure

After 3 minutes the machine will start to humidify

Weekly maintenance

Wipe the loop and inlets:

Wipe over air loop amplifier, paying close attention to the air gaps.

Wipe with a lint-free microfibre cloth.

Clean the tank

Empty the water tank.

Rinse and wipe over all surfaces.

Repeat if necessary.

Empty the trough

Tip the contents of the trough into the sink

Wipe away any spillages

Clean the base

WARNING: Do not rinse under the tap or put in the dishwasher.

While not dangerous, care should be taken to avoid water entering the inlets.

Wipe the exterior with a lint free microfibre cloth.

Replace the batteries

Replace the batteries in the remote control.

Test the Main body controls

Test the controls on the Main body of the machine.

Press the button to turn the machine on or off.

Press and hold the button to adjust the humidity.

The airspeed cannot be adjusted using the controls on the machine.

Clean the machine

This may be caused by water that has been sitting in the machine for too long.

This can likely be resolved by a thorough clean of the machine.

Twist the plug a quarter of a turn clockwise and lift out.

Unplug the machine

Please unplug the machine, leave for a minimum of 5 seconds or until the LED goes out.

Plug in and test the machine.

Main body controls

Press the button to turn the machine on or off.

Press and hold the button to adjust the humidity.

The airspeed and timer functions cannot be adjusted using the controls on the machine.

Empty the tank

Remove the loop amplifier:

Push the button to unlock the loop amplifier

Lift the loop away from the tank

Lift the tank away from the base.

Carefully empty the water from the trough in the base and undo the red cap on the underside of the tank and pour away the water.

Replace the cap.

Replace the tank and ensure it is fitted flush.

When replacing the loop ensure it 'clicks' into place securely.

Some water may be present on the underside of the tank as it is removed.

Know your humidifier

Remote control

Loop amplifier.

Power cord.

Handle.

Seal.

Water tank.

Water tank plug.

Tank chimney.

Loop release button.

Main body.

UV-C emitter.

Piezo.

LED display.

ON/OFF button.

Air inlet.

Positioning machine

When carrying, ensure the machine is level and do not lift by the loop amplifier.

Always place the machine on a firm, flat, level surface, otherwise the machine will not operate.

It is recommended that a waterproof mat or pad is placed under the machine.

WARNING: Do not place the machine in an area where it is accessible to children.

If the machine is tilted, the blue LED surrounding the Standby ON/OFF button will flash if the base is not level.

When the machine is tilted by over 5° the display will show a 'tilted' graphic.

If the machine has been tilted ensure it is level and to clear up any spillage. If the machine is not levelled after 15 minute, it will switch 'OFF'.

Where to position your machine

For the best performance, place on the floor, in the corner of the room, at least 1m from any wall and facing into the centre of the room.

Always place the machine on a firm, flat, level surface, otherwise the machine will not operate.

Consider placing near to air conditioning or heating devices to circulate air effectively.

Do not place the machine underneath overhanging surfaces.

To avoid a cooling effect while humidifying, the unit should be at least 1m from any people.

WARNING: Do not place the machine on a rug, carpet, wooden flooring, or any other surface that may be damaged by exposure to water or moisture. Do not place the machine in an area where it is accessible to children.

Using the remote control

On/Off

Fan only mode

Airspeed control

Manual humidity level control

Sleep timer

Automatic humidity mode

Aim the remote at the base of the machine.

Adjust the humidity

The AM10 can automatically adjust to the optimal humidity based on environmental conditions of the surrounding area.

The machine will switch on and off as necessary to maintain the optimal humidity level.

Press the 'Auto' button on the remote to start this mode.

You can also manually set the target humidity (between 30% and 70%) via the remote. The machine will then turn itself on and off automatically to maintain the target humidity.

Adjust the airflow

Adjust the airflow between 1 and 10 using the remote.

The selected level is displayed on the front of the machine for 3 seconds after it is set.

While using the machine in fan mode, the airflow can still be adjusted without water in the tank. Press the fan only button to turn off the humidification function.

Set the sleep timer

To set the sleep timer, press the clock button on the remote until the desired time is displayed on the machine (15 minutes to 9 hours).

When the time reaches zero, the appliance will go into standby mode. To cancel the timer, press the button again until two dashes appear.

Serial number location

Ensure all the water has been emptied from the machine before checking for the serial number.

The serial number can be found on the base of the machine.

Store the machine

When not in use, unplug from the mains electricity supply.

Store the machine in a dry location and arrange the cable away from traffic areas so that it will not be tripped over or damaged.

Clean the machine and tank according to the monthly cleaning process before storing and reusing.

Store the machine indoors.

Do not use or store it below 5°C (41°F).

Please open the PDF for the user guide.

Replace the UV-C emitter

Parts of the machine may become hot during operation. Switch off and unplug the machine for 10 minutes before replacing the emitter.

Remove the loop amplifier

Press the button at the base of the loop.

Lift the loop off the tank.

Lift the tank off the base.

Tip any water out of the base.

Remove the cover

Undo the screw with a Phillips screwdriver.

Remove the emitter

Press the catch on the wire connector

Gently remove the connector from its socket

Slide the emitter out of the machine

Fit the new emitter

Reverse step 4 to attach the new emitter.

Reassemble the machine

Instructions are provided with each replacement emitter.

Replacing the Piezo

Parts of the machine may become hot during operation. Switch off and unplug the machine for 10 minutes before replacing the piezo.

Remove the loop amplifier

• Press the button at the base of the loop
• Lift the loop off the tank
• Lift the tank of the base

Tip any water out of the base.

Remove the cover

Undo the screw with a Phillips screwdriver.

Remove the Piezo

• Press the catch on the wire connector
• Gently remove the connector from its socket
• Undo the two screws with a Phillips screwdriver and remove the piezo

Fit the new Piezo

Reverse step 4 to attach the new piezo.

Reassemble the machine