Skip navigation Accessibility Statement
Thanks. We've saved your preferences.
You can update your contact preferences at any time in the Keep in touch section of Your Dyson. If you have a Your Dyson account, you can log in below to manage your contact options.

Let's get your machine working

Dyson V11 Torque Drive (Black)
See all steps

Please select the appropriate option

Low battery

Fully charge the machine.

Troubleshooting image

The machine should be charged with the battery attached to the machine.

Please select the next step

Please ensure the battery is charged to 100% after every use.

Charge the machine

Connect to the charger either directly or in the docking station.

The blue LEDs on each side of the battery should light up.

Which lights are showing?

The blue LEDs – one on each side of the battery – will flash on and off during charging.

When the battery is charged, both LEDs will light for 5 seconds, then go out.

The screen will also show the battery charge level at 100%.

Troubleshooting image

The machine can take up to 4.5 hours to fully charge.

Has this resolved the problem?

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

Pull the trigger

Remove the charger from the machine and pull the trigger.

The LED lights should be on constantly when in use.

If the LED lights blink on/off for approximately 10 seconds when the trigger is pulled, please select 'LED lights blinking'.

Do the blue LED lights appear on either side of the battery?

You might need a replacement part.

You can solve this by ordering a new Main body & cyclone below or you can contact our Customer Support Team at 1-866-314-8881.

Main body & cyclone

Part no. 965321-01

Replacement main body and cyclone for your Dyson cordless vacuum.

$129.99

Main body & cyclone

Main body & cyclone

Part no. 965321-01

Replacement main body and cyclone for your Dyson cordless vacuum.

$129.99

$129.99

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

You might need a replacement part.

You can solve this by ordering a new Main body & cyclone below or you can contact our Customer Support Team at 1-866-314-8881.

Main body & cyclone

Part no. 965321-01

Replacement main body and cyclone for your Dyson cordless vacuum.

$129.99

Main body & cyclone

Main body & cyclone

Part no. 965321-01

Replacement main body and cyclone for your Dyson cordless vacuum.

$129.99

$129.99

Dock charging

If the machine is being charged through the docking station, please disconnect the charger and connect it directly into the machine.

Troubleshooting image

Please check household electrics or use an alternative plug socket.

Do the blue LED lights now appear on either side of the battery?

Remove the charger

Press and hold the trigger for 10 seconds.

Does the display screen show a low battery indicator?

You might need a replacement part.

You can solve this by ordering a new Battery below or you can contact our Customer Support Team at 1-866-314-8881.

Battery

Part no. 970938-01

<p>Replacement battery for your Dyson V15 Detect&trade;, Dyson Outsize and Dyson V11&trade; vacuum.&nbsp;Please be aware Dyson V11&trade; vacuums use two types of battery. Some use a click-in battery while others use a standard screw-in battery. You will be able to tell by checking your machine where the handle meets the battery. If there is a large red button that releases your battery from the main body, then your machine will need this click in battery.&nbsp;</p>

$149.99

Battery

Battery

Part no. 970938-01

<p>Replacement battery for your Dyson V15 Detect&trade;, Dyson Outsize and Dyson V11&trade; vacuum.&nbsp;Please be aware Dyson V11&trade; vacuums use two types of battery. Some use a click-in battery while others use a standard screw-in battery. You will be able to tell by checking your machine where the handle meets the battery. If there is a large red button that releases your battery from the main body, then your machine will need this click in battery.&nbsp;</p>

$149.99

$149.99

How to install this part

You might need a replacement part.

You can solve this by ordering a new Charger below or you can contact our Customer Support Team at 1-866-314-8881.

Charger

Part no. 969350-02

<div>Charges your vacuum with or without the Wall Dok™.</div>

$29.99

Charger

Charger

Part no. 969350-02

<div>Charges your vacuum with or without the Wall Dok™.</div>

$29.99

$29.99

The blue LEDs – one on each side of the battery – will flash on and off during charging.

When the battery is charged, both LEDs will light for 5 seconds, then go out.

The screen will also show the battery charge level at 100%.

Troubleshooting image

The machine can take up to 4.5 hours to fully charge.

Has this resolved the problem?

Automatic cut out

Large items may block the machine or tools. If any part becomes blocked or the filter needs washing, the machine may automatically cut out.

Troubleshooting image

Motor is pulsating

This will happen after the motor pulses a number of times (i.e. switches on and off in quick succession) and the blockage indicator will light. Leave to cool down before looking for blockages.

Be careful not to pull the 'ON' trigger while looking for blockages. Operating the machine while it is partially dismantled could result in personal injury.

Remove the tools

Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Does the alert still appear?

Check for blockages

Check both ends of the wand for blockages and remove as necessary.

Troubleshooting image

Reattach the cleaner head, tool or accessory to the wand. Reattach the wand to the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Check for blockages

With the accessory removed from the machine, check both ends for blockages and remove as necessary.

Refit the accessory back onto the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Check the bin inlet

Check the inlet at the front of the machine for any blockages and remove as necessary.

Troubleshooting image

Check the shroud opening

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Remove the bin

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Press the red button located on the bin runner to release the bin and slide the bin off the runner.

Troubleshooting image

Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone. Using the combination tool, clean the shroud to remove any debris around the cyclone.

Check the cyclone for blockages and remove as necessary.

Troubleshooting image

To refit the clear bin

Insert the spine into the bin runner.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Attach the wand and cleaner head and test the machine.

Has this resolved the problem?

This indicates the filter needs washing. Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.

Press and hold the trigger for 10 seconds.

Removing the filter

Remove the filter by turning it anticlockwise. Gently pull it away from the machine.

Gently tap the filter unit to remove any excess dust and debris before washing it.

Wash the filter in cold water only.

WARNING: Please do not use detergent, do not wash in a dishwasher or washing machine.

Wash the pleated paper element of the filter unit first; hold the filter unit under a cold water tap with the foam element downwards and run cold water over the pleated paper. Continue washing until the water runs clear.

Wash the foam element of the filter unit next; hold the filter unit under a cold water tap with the foam element downwards so that dirty water does not contaminate the pleated paper element. Run cold water over the inside and outside of the foam element and squeeze the foam gently to expel the dirt. Continue washing until the water runs clear.

Wash the outside of the filter unit. Then fill the unit with cold water, place your hands over the open ends and shake gently. Repeat washing the elements and outside of the filter unit until the water runs clear.

Drying

Leave the filter unit to dry completely in a dry environment with good airflow, for a minimum of 24 hours. Check that the filter unit is completely dry.

Refit

To refit, return the filter unit to the main body and twist clockwise until it clicks into place.

The filter unit may require more frequent washing if vacuuming fine dust or if use is mainly in Boost mode.

Has this resolved the problem?

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Clear the floor tool

On the side of the cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Troubleshooting image

Remove the brush bar from the Direct drive cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

Has this resolved the problem?

Clear the floor tool

On the side of the cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Remove the brush bar from the High Torque cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Place the cleaner head onto the bin, change the suction control slider to the positive position and test the machine.

Switch the suction control slider to the negative setting and continue testing.

Has this resolved the problem?

Clear the floor tool

On the side of the Mini motorised head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Remove the brush bar from the Quick-release Mini motorised head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

Has this resolved the problem?

Clear the floor tool

Under the cleaner head by the soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.

Troubleshooting image

Remove the brush bar from the Soft roller cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

The Soft roller cleaner head has two washable brush bars. Check and wash them regularly as per the step by step instructions.

Has this resolved the problem?

Please follow the steps in the video.

Washable brush bars - step by step

With the cleaner head removed from the machine, turn it upside down so the underside of the cleaner head is facing you. Use a coin to turn the end cap a quarter anticlockwise until it clicks into the unlocked position. Rotate the end cap to the open position. Gently slide the main brush bar out of the cleaner head. Remove the end cap from the main brush bar. Do not wash the end cap.

Troubleshooting image

Gently slide the rear brush bar out of the cleaner head.

Troubleshooting image

Hold the brush bars under running water and gently rub to remove any lint or dirt.

Troubleshooting image

Stand the brush bars upright. Leave to dry completely for a minimum of 24 hours. Before replacing, check that the brush bars are completely dry.

Troubleshooting image

Slide the rear brush bar back into the cleaner head.

Troubleshooting image

Reattach the end cap to the large brush bar.

Slide the main brush bar back into the cleaner head.

The end cap should be in the open position. Once in place, rotate the end cap back into the closed position.

Close the fastener by turning it a quarter clockwise. Ensure that the fastener is fully turned and the brush bars are secure.

Troubleshooting image

Refit the cleaner head on the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Check the bin inlet

Check the inlet at the front of the machine for any blockages and remove as necessary.

Troubleshooting image

Check the shroud opening

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Diagnostic screen

The menu is accessed by pressing the selector button with the filter removed. Three options are displayed when accessing this menu screen.

Versions, displays the software versions of the machine.

Diagnostic, displays a series of numbers, letters and percentages.

Exit, you can exit the menu by selecting this option.

Troubleshooting image

Check the filter

Before exiting the menu, please ensure the filter is fitted correctly.

The filter unit should be securely fitted onto the main body and turned clockwise until it clicks into place.

Troubleshooting image

Exiting the menu

Once the filter is securely in place, press and hold the selector button for approximately 10 seconds or until the screen reverts back to the main display screen.

Troubleshooting image

Has this resolved the problem?

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

If you are unable to revert back to the main display screen manually, it can be achieved by leaving the machine to go inactive (around 15 minutes of no interaction).

Has this resolved the problem?

If the filter isn't correctly fitted, the machine will not turn on when pressing the trigger.

Troubleshooting image

Removing the filter

Remove the filter by turning it anticlockwise. Gently pull it away from the machine.

Troubleshooting image

Refit

Insert the filter back into the machine. Turn the filter clockwise until it clicks into place.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

This alert will continue until maintenance has been carried out.

This indicates the filter needs washing.

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has washing the filter resolved the problem?"

Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.

Press and hold the trigger for 10 seconds.

Has washing the filter resolved the problem?

The filter may need to be washed more frequently if you are vacuuming a lot of fine dust, or if the machine is predominantly being used in Eco mode or Auto/Medium mode.

Removing the filter

Remove the filter by turning it anticlockwise. Gently pull it away from the machine.

Troubleshooting image

Gently tap the filter unit to remove any excess dust and debris before washing it.

Wash the filter in cold water only.

WARNING: Please do not use detergent, do not wash in a dishwasher or washing machine.

Wash the pleated paper element of the filter unit first; hold the filter unit under a cold water tap with the foam element downwards and run cold water over the pleated paper. Continue washing until the water runs clear.

Troubleshooting image

Wash the foam element of the filter unit next; hold the filter unit under a cold water tap with the foam element downwards so that dirty water does not contaminate the pleated paper element. Run cold water over the inside and outside of the foam element and squeeze the foam gently to expel the dirt. Continue washing until the water runs clear.

Troubleshooting image

Wash the outside of the filter unit. Then fill the unit with cold water, place your hands over the open ends and shake gently. Repeat washing the elements and outside of the filter unit until the water runs clear.

Troubleshooting image

Gently shake the filter unit to remove any excess water and leave to drain with the foam element end facing up.

Troubleshooting image

Drying

Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.

Troubleshooting image

Refit

Insert the filter back into the machine. Turn the filter clockwise until it clicks into place.

Troubleshooting image

Has washing the filter resolved the problem?

This alert will continue until maintenance has been carried out.

Troubleshooting image

This indicates the filter needs washing.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.

Press and hold the trigger for 10 seconds.

Check the bin inlet

Check the inlet at the front of the machine for any blockages and remove as necessary.

Troubleshooting image

Check the shroud opening

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Close the clear bin by pushing the bin base upwards until it clicks into place.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Before testing the machine please ensure that any hair or loose clothing is clear of the machine.

Automatic cut out

Large items may block the machine or tools. If any part becomes blocked or the filter needs washing, the machine may automatically cut out.

Motor is pulsating

1 solid blue light will indicate the machine has a low level of charge.

If the machine is cutting out/pulsating, this will indicate a blockage.

Be careful not to pull the 'ON' trigger while looking for blockages. Operating the machine while it is partially dismantled could result in personal injury.

Remove the tools

Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Does the machine still pulsate?

Check for blockages

Check both ends of the wand for blockages and remove as necessary.

Troubleshooting image

Reattach the cleaner head, tool or accessory to the wand. Reattach the wand to the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Check for blockages

With the accessory removed from the machine, check both ends for blockages and remove as necessary.

Refit the accessory back onto the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Check the bin inlet

Check the inlet at the front of the machine for any blockages and remove as necessary.

Troubleshooting image

Check the shroud opening

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Clear the floor tool

On the side of the cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Troubleshooting image

Remove the brush bar from the Direct drive cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

Has this resolved the problem?

Clear the floor tool

On the side of the cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Remove the brush bar from the High Torque cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Place the cleaner head onto the bin, change the suction control slider to the positive position and test the machine.

Switch the suction control slider to the negative setting and continue testing.

Has this resolved the problem?

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Clear the floor tool

On the side of the Mini motorised head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Remove the brush bar from the Quick-release Mini motorised head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

Has this resolved the problem?

Clear the floor tool

Under the cleaner head by the soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to unlock the end cap, and slide it up to remove.

Troubleshooting image

Remove the brush bar from the Soft roller cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

The Soft roller cleaner head has two washable brush bars. Check and wash them regularly as per the step by step instructions.

Has this resolved the problem?

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Washing the brush bars

With the cleaner head removed from the machine, turn it upside down so the underside of the cleaner head is facing you. Use a coin to turn the end cap a quarter anticlockwise until it clicks into the unlocked position. Rotate the end cap to the open position. Gently slide the main brush bar out of the cleaner head. Remove the end cap from the main brush bar. Do not wash the end cap.

Troubleshooting image

Gently slide the rear brush bar out of the cleaner head.

Troubleshooting image

Hold the brush bars under running water and gently rub to remove any lint or dirt.

Troubleshooting image

Stand the brush bars upright. Leave to dry completely for a minimum of 24 hours. Before replacing, check that the brush bars are completely dry.

Slide the rear brush bar back into the cleaner head.

Troubleshooting image

Reattach the end cap to the large brush bar.

Troubleshooting image

Slide the main brush bar back into the cleaner head.

Troubleshooting image

The end cap should be in the open position. Once in place, rotate the end cap back into the closed position.

Refit the cleaner head on the machine.

Troubleshooting image

Close the fastener by turning it a quarter clockwise. Ensure that the fastener is fully turned and the brush bars are secure.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Check the bin inlet

Check the inlet at the front of the machine for any blockages and remove as necessary.

Troubleshooting image

Check the shroud opening

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Test the machine

Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.

Troubleshooting image

Put the machine in Boost mode.

Press and hold the trigger for 10 seconds.

Does the noise still occur?

Remove the bin

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Press the red button located on the bin runner to release the bin and slide the bin off the runner.

Troubleshooting image

Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone. Using the combination tool, clean the shroud to remove any debris around the cyclone.

Press and hold the trigger for 10 seconds.

Does the noise still occur?

Check the bin inlet

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Troubleshooting image

To refit the clear bin

Insert the spine into the bin runner.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

We need a little more information to help us solve your issue.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen. Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Before testing the machine please ensure that any hair or loose clothing is clear of the machine.

Automatic cut out

Large items may block the machine or tools. If any part becomes blocked or the filter needs washing, the machine may automatically cut out.

Motor is pulsating

1 solid blue light will indicate the machine has a low level of charge.

If the machine is cutting out/pulsating, this will indicate a blockage.

Be careful not to pull the 'ON' trigger while looking for blockages. Operating the machine while it is partially dismantled could result in personal injury.

Remove the tools

Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Does the machine still pulsate?

Before testing the machine please ensure that any hair or loose clothing is clear of the machine.

The suction power of the machine varies depending which power mode you have selected. Boost mode being the most powerful.

Pick up issues are typically caused by a blockage.

Be careful not to pull the 'ON' trigger while looking for blockages. Operating the machine while it is partially dismantled could result in personal injury.

Remove the tools

Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Is the machine pulsating?

If your machine has recently been fully charged but the battery alert is still present, we recommend that you place the machine back on charge for a few moments.

Troubleshooting image

The display will again show that the battery is fully charged.

Troubleshooting image

Remove the charger from the machine and pull the trigger.

Troubleshooting image

Has this resolved the problem?

You might need a replacement part.

You can solve this by ordering a new Charger below or you can contact our Customer Support Team at 1-866-314-8881.

Charger

Part no. 969350-02

<div>Charges your vacuum with or without the Wall Dok™.</div>

$29.99

Charger

Charger

Part no. 969350-02

<div>Charges your vacuum with or without the Wall Dok™.</div>

$29.99

$29.99

Please ensure the battery is charged to 100% after every use.

Power modes

The machine has three power modes for different tasks. The overall run time is displayed on the digital display screen in minutes and seconds and will vary between each of the three power modes.

Run time

The overall run time can increase and decrease depending on the power mode, floor type and tool being used. Any change to the run time can take up to 30 seconds to appear on the digital display.

Eco mode

Maximum run time for longer cleans all around your home, with up to 60 minutes of run time.

Troubleshooting image

Med mode

The optimum balance to clean all floors, with up to 40 minutes of run time.

Troubleshooting image

Boost mode

Designed for intensive cleaning on ground-in dirt, with up to 5 minutes of run time.

Troubleshooting image

Please ensure the battery is charged to 100% after every use.

When the machine is placed on charge it enters an idle state, this reduces all power consumption ready for the next use. Due to this reduction in the power, when the machine is removed from charge and powered on for the first time it can display an incorrect run time. This is nothing to be concerned about. The machine will assess the charge capacity and current usage within 30 seconds, displaying the correct time on the digital display.

To achieve the maximum run time, the machine must first be calibrated. The machine should be fully charged approximately five times. Between charges, use the machine until it has no battery remaining.

Where you have additional click-in batteries, we recommend alternating and charging all click-in batteries regularly to prolong battery health.

Charge the machine

Connect to the charger either directly or in the docking station.

Troubleshooting image

Do the blue LED lights appear on either side of the battery?

Charge the machine

When the battery is charged, both LEDs will light for 5 seconds, then go out.

Remove the charger

Press and hold the trigger for 10 seconds.

Does the machine have power?

Pull the trigger

Press and hold the trigger for 10 seconds.

The LED lights should be on constantly when in use.

If the LED lights blink on/off for approximately 10 seconds when the trigger is pulled, please select 'LED lights blinking'.

Do the blue LED lights appear on either side of the battery?

Charging

If the machine is being charged through the docking station, please disconnect the charger and connect it directly into the machine.

Troubleshooting image

Please check household electrics or use an alternative plug socket.

Do the blue LED lights now appear on either side of the battery?

Remove the charger

Press and hold the trigger for 10 seconds.

Does the display screen show a low battery indicator?

You might need a replacement part.

You can solve this by ordering a new Battery below or you can contact our Customer Support Team at 1-866-314-8881.

Battery

Part no. 970938-01

<p>Replacement battery for your Dyson V15 Detect&trade;, Dyson Outsize and Dyson V11&trade; vacuum.&nbsp;Please be aware Dyson V11&trade; vacuums use two types of battery. Some use a click-in battery while others use a standard screw-in battery. You will be able to tell by checking your machine where the handle meets the battery. If there is a large red button that releases your battery from the main body, then your machine will need this click in battery.&nbsp;</p>

$149.99

Battery

Battery

Part no. 970938-01

<p>Replacement battery for your Dyson V15 Detect&trade;, Dyson Outsize and Dyson V11&trade; vacuum.&nbsp;Please be aware Dyson V11&trade; vacuums use two types of battery. Some use a click-in battery while others use a standard screw-in battery. You will be able to tell by checking your machine where the handle meets the battery. If there is a large red button that releases your battery from the main body, then your machine will need this click in battery.&nbsp;</p>

$149.99

$149.99

How to install this part

The blue LEDs – one on each side of the battery – will flash on and off during charging.

When the battery is charged, both LEDs will light for 5 seconds, then go out.

The machine can take up to 4.5 hours to fully charge.

Remove the charger

Press and hold the trigger for 10 seconds.

Does the machine have power?

Most Dyson vacuums have a built in safety mechanism that will turn off the machine if it begins to overheat. This typically happens when the machine is blocked, or if the filter needs washing.

If your machine continues to overheat, please allow it to cool before carrying out the performance checks.

Please select the next step

Before testing the machine please ensure that any hair or loose clothing is clear of the machine.

Automatic cut out

This machine is fitted with an automatic cut out. If any part becomes blocked, the machine may automatically cut out.

Motor is pulsating

This will happen after the motor pulses a number of times (i.e. switches on and off in quick succession) and the blockage indicator will light. Leave to cool down before looking for blockages.

Be careful not to pull the 'ON' trigger while looking for blockages. Operating the machine while it is partially dismantled could result in personal injury.

Remove the tools

Remove all tools and accessories from the machine e.g. wand, cleaner head, crevice tool etc. Please ensure the bin is empty before continuing with any checks.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Check the bin inlet

Check the inlet at the front of the machine for any blockages and remove as necessary.

Troubleshooting image

Check the shroud opening

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Check for blockages

Check both ends of the wand for blockages and remove as necessary.

Troubleshooting image

Reattach the cleaner head, tool or accessory to the wand. Reattach the wand to the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Charge the machine

Connect to the charger either directly or in the docking station.

Troubleshooting image

The blue LEDs – one on each side of the battery – will flash on and off during charging.

Do the blue LED lights appear on either side of the battery?

Charge the machine

When the battery is charged, both LEDs will light for 5 seconds, then go out.

Remove the charger

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

Has the machine been fully charged?

The Dyson V11™ battery and monitoring system work together to gauge how much run time is remaining. The system calculates run time using an algorithm that ‘learns’ how your machine works over time. To get the best experience, we recommend fully charging your machine after every use. This helps the battery and monitoring system's algorithm to more accurately calculate and display remaining run time.

The actual run time of your machine remains unaffected while the algorithm learns to more accurately gauge remaining power.

The battery is designed to be left on charge permanently, and this will ensure that the machine is fully charged when it's next used. It will take up to 4.5 hours to fully charge your machine. Once the battery is fully charged, your machine won't use any more electricity.

Has this resolved the problem?

If your machine continues to cut out even though run time remains on the screen, we recommend fully charging your machine, then using it continuously until the battery runs out. This should be completed within one cleaning session, but the trigger doesn't need to be held down throughout. We advise using Auto/Med mode for this clean. The more this process is repeated, the more accurate the algorithm becomes.

The battery is designed to be left on charge permanently, and this will ensure that the machine is fully charged when it's next used. It will take up to 4.5 hours to fully charge your machine. Once the battery is fully charged, your machine won't use any more electricity.

Has this resolved the problem?

Please select the appropriate option

Damp or musty

A damp or musty smell is caused when dust in the cyclone has come into contact with water.

It may not be a direct contact with water, for example when vacuuming pet hair that is slightly damp, this moisture will combine with the dust in the cyclone causing the smell.

Additionally the smell may occur if the filter goes back into the machine wet.

Only the filter and the two washable brush bars from the Soft roller cleaner head can be washed. The bin can be cleaned with a damp cloth only. Washed and cleaned parts must be completely dry before being refitted to the machine.

Has any part of the machine been washed?

Remove the bin

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Press the red button located on the bin runner to release the bin and slide the bin off the runner.

Troubleshooting image

Gently tap the side of the cyclone over a bin. This will remove any fine dust clogged up in the cyclone. Using the combination tool, clean the shroud to remove any debris around the cyclone.

Check the opening on the cyclone shroud for any blockages. Remove as necessary.

Troubleshooting image

The clear bin is not dishwasher safe and the use of detergents, polishes or air fresheners to clean the clear bin is not recommended as this may damage your machine. Clean the clear bin with a damp cloth only.

To refit the clear bin

Insert the spine into the bin runner.

Troubleshooting image

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Has this resolved the problem?

This indicates the filter needs washing. Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.

Press and hold the trigger for 10 seconds.

Damp or musty smell still present

Under normal use, any unpleasant smell can only be caused by something the machine has picked up. Please select pick up issues to carry out checks.

Removing the filter

Remove the filter by turning it anticlockwise. Gently pull it away from the machine.

Troubleshooting image

Gently tap the filter unit to remove any excess dust and debris before washing it.

Wash the filter in cold water only.

WARNING: Please do not use detergent, do not wash in a dishwasher or washing machine.

Wash the pleated paper element of the filter unit first; hold the filter unit under a cold water tap with the foam element downwards and run cold water over the pleated paper. Continue washing until the water runs clear.

Troubleshooting image

Wash the foam element of the filter unit next; hold the filter unit under a cold water tap with the foam element downwards so that dirty water does not contaminate the pleated paper element. Run cold water over the inside and outside of the foam element and squeeze the foam gently to expel the dirt. Continue washing until the water runs clear.

Troubleshooting image

Wash the outside of the filter unit. Then fill the unit with cold water, place your hands over the open ends and shake gently. Repeat washing the elements and outside of the filter unit until the water runs clear.

Troubleshooting image

Gently shake the filter unit to remove any excess water and leave to drain with the foam element end facing up.

Troubleshooting image

Drying

Leave the filter to dry for a minimum of 24 hours in an environment with good airflow. Ensure that the filter is completely dry before reinserting it into the machine.

Troubleshooting image

Refit

Insert the filter back into the machine. Turn the filter clockwise until it clicks into place.

Troubleshooting image

The filter may need to be washed more frequently if you are vacuuming a lot of fine dust, or if the machine is predominantly being used in Eco mode or Auto/Medium mode.

Has this resolved the problem?

Were all the washed parts completely dry before the machine was used?

Damp or musty smell still present

Under normal use, any unpleasant smell can only be caused by something the machine has picked up. Please select pick up issues to carry out checks.

If you are able to identify which part of the machine the smell is coming from, replacing this part may resolve the issue.

We need a little more information to help us solve your issue.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen. Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

We need a little more information to help us solve your issue.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen. Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Please check all floor tools

Please connect the floor tool directly on to the bin.

If the brush bar on every tool spins when connected to the bin, please select "The wand is damaged".

If the brush bar isn't spinning on any tool, please select "The brush bar does not spin on any cleaner head".

Clear the floor tool

With the Direct drive cleaner head removed from the machine, turn it over and undo the fastener.

Locate the end cap and using a coin, turn it anticlockwise a quarter of the way. This will allow you to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Troubleshooting image

Remove the brush bar from the Direct drive cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

Has this resolved the problem?

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

_

Clear the floor tool

With the High Torque cleaner head removed from the machine, turn it over and undo the fastener.

Locate the end cap and using a coin, turn it anticlockwise a quarter of the way. This will allow you to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Remove the brush bar from the High Torque cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Place the cleaner head onto the bin, change the suction control slider to the positive position and test the machine.

Switch the suction control slider to the negative setting and continue testing.

Has this resolved the problem?

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Clear the floor tool

With the Quick-release Mini motorised head removed from the machine, turn it over and undo the fastener. Locate the end cap and using a coin, turn it anticlockwise a quarter of the way. This will allow you to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Troubleshooting image

Remove the brush bar from the Quick-release Mini motorised head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

Has this resolved the problem?

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Clear the floor tool

With the cleaner head removed from the machine, turn it over. On the underside of the cleaner head by the soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to remove the end cap.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Troubleshooting image

Remove the brush bar from the Soft roller cleaner head and clear away any hair or fibres. Check the neck of the cleaner head (where the cleaner head connects to the wand) for any blockages. Ensure there is no build-up of dust or debris in the small crevice between where the brush bar sits and the neck of the cleaner head.

Troubleshooting image

The brush bar, now clear of any debris, can be reinserted into the cleaner head. Securely fasten the end cap.

Troubleshooting image

The Soft roller cleaner head has two washable brush bars. Check and wash them regularly as per the step by step instructions.

Has this resolved the problem?

Please follow the steps in the video.

Washable brush bars - step by step

With the cleaner head removed from the machine, turn it upside down so the underside of the cleaner head is facing you. Use a coin to turn the end cap a quarter anticlockwise until it clicks into the unlocked position. Rotate the end cap to the open position. Gently slide the main brush bar out of the cleaner head. Remove the end cap from the main brush bar. Do not wash the end cap.

Troubleshooting image

Gently slide the rear brush bar out of the cleaner head.

Hold the brush bars under running water and gently rub to remove any lint or dirt.

Stand the brush bars upright. Leave to dry completely for a minimum of 24 hours. Before replacing, check that the brush bars are completely dry.

Slide the rear brush bar back into the cleaner head.

Slide the main brush bar back into the cleaner head.

Reattach the end cap to the large brush bar.

The end cap should be in the open position. Once in place, rotate the end cap back into the closed position.

Close the fastener by turning it a quarter clockwise. Ensure that the fastener is fully turned and the brush bars are secure.

Refit the cleaner head on the machine.

Press and hold the trigger for 10 seconds.

Has this resolved the problem?

You might need a replacement part.

You can solve this by ordering a new Main body & cyclone below or you can contact our Customer Support Team at 1-866-314-8881.

Main body & cyclone

Part no. 965321-01

Replacement main body and cyclone for your Dyson cordless vacuum.

$129.99

Main body & cyclone

Main body & cyclone

Part no. 965321-01

Replacement main body and cyclone for your Dyson cordless vacuum.

$129.99

$129.99

Apologies. We can’t help you online.

Please contact our Customer Support Team by calling 1-866-314-8881 or by clicking the Live Chat button in the bottom right corner of your screen.

Dyson Supersonicᵀᴹ hair dryer Professional edition owners should call 1-866-861-2565.

Please ensure that you are emptying the bin as soon as the dirt reaches the level of the MAX mark.

Troubleshooting image

Should the dirt in the bin exceed the MAX mark, the excess dirt can be pulled directly into the filter causing a blockage.

Has this resolved the problem?

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Has this resolved the problem?"

Empty as soon as the dirt reaches the level of the MAX mark - do not overfill. Ensure the machine is disconnected from the charger before emptying the clear bin. Be careful not to pull the 'ON' trigger.

Troubleshooting image

Remove the wand by pressing the red wand release button and pulling away from the bin.

Troubleshooting image

Emptying the bin

Hold the machine with the bin in a downwards position. Firmly push the red bin release button. The bin will slide down opening the bin base. The bin base will not open if the red button is not pushed down fully.

Troubleshooting image

Closing the bin

Close the clear bin by pushing the bin base upwards until it clicks into place.

Troubleshooting image

Has this resolved the problem?

Scratches or marks on the wand

Marks on the wand can be caused by making contact with a painted surface such as a door frame.

These can be removed by wiping them with a damp cloth.

Has this resolved the problem?

You might need a replacement part.

You can solve this by ordering a new Wand (Black) below or you can contact our Customer Support Team at 1-866-314-8881.

Wand (Black)

Part no. 969109-13

<p>Replacement&nbsp;Wand (Black) for your Dyson cordless vacuum.</p>

$29.99

Wand (Black)

Wand (Black)

Part no. 969109-13

<p>Replacement&nbsp;Wand (Black) for your Dyson cordless vacuum.</p>

$29.99

$29.99