For the best performance, always fully charge your Dyson Corrale™ straightener between uses.

When your straightener needs charging, the battery icon on the OLED screen will flash and a prompt will sound.

When the battery is empty, the battery icon will flash and a prompt will sound five seconds before your straightener turns off.

The battery charging LED is located on the lower part of the Dyson Corrale™ straightener. The LED will be amber while charging and turn green when fully charged.

Charge your Dyson Corrale™ straightener on the dock or directly with the Magnetic 360° charging cable.

If your straightener is turned off, a prompt will sound when you connect to the Magnetic 360° charging cable.

Hybrid charge mode

You can use your straightener with the Magnetic 360° charging cable attached. This will extend the run time but you'll still need to fully charge between uses, as you will still be using battery power when styling.

We recommend that you fully charge your straightener before using in Hybrid mode.

Too hot

Reset

Charger error

Call Dyson

Flight-ready

Turn the machine off.

Please try another socket.

Ensure the Magnetic 360° charging cable is free of debris.

Turn on and test the machine.

Please check whether your Flight-ready tag has two or four pins.

Please follow the steps in the video.

When the Flight-ready tag is removed, all controls will be disabled. If you try to use your straightener when flight-ready, an aeroplane icon will appear on the OLED screen.

If the aeroplane symbol doesn't appear on the OLED screen when the Flight-ready tag is removed, contact Dyson before travelling.

Reactivating your straightener

Insert the Flight-ready tag back into your straightener.

Please follow the steps in the video.

When the Flight-ready tag is in position, all of the controls will be disabled. If you try to use your straightener when flight-ready, an aeroplane icon will appear on the OLED screen.

If the aeroplane symbol doesn't appear on the OLED screen when the Flight-ready tag is in position and the Power button is pressed, contact Dyson before travelling.

Reactivating your straightener

Remove, rotate and replace the Flight-ready tag to align with the house symbol.

Turn your straightener off and then back on again to reset.

Turn your straightener off and leave to cool down.

This is expected if the ambient temperature is very hot or the machine is next to a heat source.

Understanding the sounds

Please follow the steps in the video.

Ensure the Lock button is clear of any debris and moves freely.

For the best performance, always fully charge your Dyson Corrale™ straightener between uses.

Slide the Lock button to open your straightener.

Press and hold the Power button until a battery icon appears on the OLED screen.

Press the Temperature (+/−) control buttons to select the temperature that suits your hair type and styling preference.

The Power button will pulse red as your straightener heats up.

Your straightener is ready to use when the Power button illuminates red, a prompt sounds and a tick icon appears on the OLED screen.

Reset the machine

Turn your straightener off and then back on again to reset.

If you're having trouble gliding through your hair with the Dyson Corrale™ straightener, try the following simple steps:

• Prepare the hair: Before styling, ensure hair is tangle-free and completely dry. For best results, section your hair before starting to style.

• Loosen grip: Because the flexing plates shape to gather your hair, you don’t need to apply as much tension. Loosen the grip and let the machine do the work for you.

• Tress (hair section) size: The perfect tress size will depend on your hair type. Try a few different section sizes and see what works best for you.

If you have coarse or curly hair, try starting with smaller sections.

If you have fine hair, try using larger sections.

• Position of the tress: To maximize the benefits of the flexing plates, ensure the hair tress is in the middle of the plates when styling.

• Style speed: Try using slow, even passes rather than multiple quick passes.

• Styling your ends: If you’re finding it difficult to style the ends of your hair, it may be because you have finer or more layered hair. Try styling your roots and mid-lengths first, and style the ends last so you can take larger sections of hair.

Too hot

Turn your straightener off and leave to cool down.

This is expected if the ambient temperature is very hot or the machine is next to a heat source.

Clean the machine

Turn off your Dyson Corrale™ straightener and leave to cool before cleaning.

Clean the flexing plates with a damp, lint-free cloth. Rub gently to remove any stubborn hair product residue.

Don't use chemicals or abrasive products as this may damage the surface of the flexing plates.

For the best performance, always fully charge your Dyson Corrale™ straightener between uses.

Your Dyson Corrale™ straightener will provide up to 30 minutes of cord-free styling. However this will vary depending on heat setting and how the product is used.

Your Dyson Corrale fast charges during the first 40 minutes of being plugged in (up to ~95% of battery charge). For the remainder of the 30 minutes of charging the process slows to protect the battery from being over charged.

The greatest draw on the charge of the battery is during the heating up period; taking the heater plates from ambient/room temperature up to 210°C/410°F. Therefore, the largest drop in battery charge would be expected in the first few minutes of each use. After this, the drop in charge on the OLED will slow down as the battery only has to maintain the temperature of the plates.

If the product is fully charged for 70 minutes we would expect a 15-20% drop in charge around 5 minutes of use if the user is using the product at 210°C/410°F. However, if the product is only charged for 40 minutes we would expect there to be a 25-30% drop in charge around the 5 minutes mark for a product at 210°C/410°F. If the ambient temperature is below 20°C, this will put further pressure on the battery and the drop in charge may be greater.

If the temperature of the product is set to a lower heat setting, the drop in the battery charge on the OLED screen will be slower.

Hybrid charge mode

Connect to the Magnetic 360° charging cable to extend your run time.

The battery will continue to discharge when in Hybrid mode, but at a slower rate.

Store your Dyson Corrale™ straightener on the charging dock when not in use to maximise run time.

Styling guides

Go to www.dyson.com/mycorrale for styling tips and guides.

To ensure your Dyson Corrale™ straightener cools down after use, we would always recommend manually turning off the machine using the power button.

If your Dyson Corrale™ straightener remains hot after 10 minutes of inactivity, please contact Dyson directly.

Styling tips

For best results, detangle and section the hair first.

Place each section in the centre, so plates can gather the hair.

Experiment with section size, to see what suits your hair best.

For thick or curly hair, take smaller sections.

For finer hair, take larger sections.

Glide though hair with slow, even passes.

The plates flex, so there’s no need to apply excess pressure.

To get closer to the roots, take sections at an angle.

If your tips are thinner than your roots, style tips and mid-lengths first.

To align shorter hairs, tilt plates slightly inwards.

Reduce temperature around the delicate hairline.

Finish with your favourite smoothing product.

Ensure the Magnetic 360° charging cable is free of debris.

Place your Dyson Corrale™ straightener on the dock, ensuring that the cable is correctly attached to the dock and the plug is switched on.

If your straightener is turned off, a prompt will sound when you connect to the Magnetic 360° charging cable.

The battery charging LED is located on the lower part of the Dyson Corrale™ straightener. The LED will be amber while charging and turn green when fully charged.

If the machine is being charged at an ambient temperature below 10°C, the battery pack will not be able to fully charge. Because of this the green LED will not light up and the display will never show the full battery indicator.

Ensure the Magnetic 360° charging cable is free of debris.

Place your Dyson Corrale™ straightener on the dock, ensuring that the cable is correctly attached to the dock and the plug is switched on.

If your straightener is turned off, a prompt will sound when you connect to the Magnetic 360° charging cable.

The battery charging LED is located on the lower part of the Dyson Corrale™ straightener. The LED will be amber while charging and turn green when fully charged.

Try to charge your Dyson Corrale™ directly with the Magnetic 360° charging cable.

Press and hold the Power button until a battery icon appears on the OLED screen.

Please note, a blank screen signifies there may be a battery issue with your Dyson Corrale™ straightener. This may be accompanied by a white fast flashing on/off button. Should this occur you must not fly with the product, please contact Dyson immediately.

Charge your Dyson Corrale™ straightener on the dock or directly with the Magnetic 360° charging cable.

If your straightener is turned off, a prompt will sound when you connect to the Magnetic 360° charging cable.

Too hot

Reset

Charger error

Call Dyson

Flight-ready

When the Flight-ready tag is in position, all of the controls will be disabled. If you try to use your straightener when flight-ready, an aeroplane icon will appear on the OLED screen.

Reactivating your straightener

Insert the Flight-ready tag back into your straightener.

Reset the machine

Turn your straightener off and then back on again to reset.

Reactivating your straightener

Remove, rotate and replace the Flight-ready tag to align with the house symbol.

Run time

A full charge will provide up to 30 minutes of cord-free styling.

For the best performance, always fully charge your straightener between uses and rest on the dock (with the charger attached) when possible during styling.

For maximum run time, use in Hybrid mode.

When your straightener needs charging, the battery icon on the OLED screen will flash and a prompt will sound.

When the battery is empty, the battery icon will flash and a prompt will sound five seconds before the straightener turns off.

A 40 minutes charge time will give approximately 90% battery charge, a full charge takes 70 minutes.

Charge your Dyson Corrale™ straightener on the dock or directly with the Magnetic 360° charging cable.

If your straightener is turned off, a prompt will sound when you connect to the Magnetic 360° charging cable.

After a full charge, press the Power button to turn on your Dyson Corrale™ straightener.

Please note, a blank screen signifies there may be a battery issue with your Dyson Corrale™ straightener. This may be accompanied by a white fast flashing on/off button. Should this occur you must not fly with the product, please contact Dyson immediately.

As with many electrical products, it is normal to hear a quiet buzzing noise from the Dyson Corrale™ straightener when the machine is plugged in.

The buzzing noise may appear louder as the machine is held close to your ear during use.

Please follow the steps in the video.

Clean the machine

Turn off your Dyson Corrale™ straightener and leave to cool before cleaning.

Clean the flexing plates with a damp, lint-free cloth. Rub gently to remove any stubborn hair product residue.

Don't use chemicals or abrasive products as this may damage the surface of the flexing plates.

Within the first few uses it is normal to expect a smell from any brand new appliance with a heater element (e.g. toaster/oven/kettle etc.)

The smell will fade with time and usage.

The charging cable is connected magnetically and will come apart when force is applied. It should not detach without interaction, but may if knocked loose.

Please check whether your Flight-ready tag has two or four pins.

Getting started

Insert the Flight-ready tag into your straightener. This will enable your straightener's controls.

If unable to re-insert the Flight-ready tag, cut the tether off. Take extra care not to lose the Flight-ready tag once the tether has been removed.

If the Flight-ready tag is damaged, lost or you are experiencing another issue relating to the Flight-ready tag, this can be resolved by ordering a replacement part below.

Getting started

Insert the Flight-ready tag into your straightener. This will enable your straightener's controls.

If unable to re-insert the Flight-ready tag, cut the tether off. Take extra care not to lose the Flight-ready tag once the tether has been removed.

If the Flight-ready tag is damaged, lost or you are experiencing another issue relating to the Flight-ready tag, this can be resolved by ordering a replacement part below.

Getting started

Your Dyson Corrale™ straightener is shipped in Flight-ready mode.

Remove, rotate and replace the Flight-ready tag to align with the house symbol.

If the Flight-ready tag is damaged, lost or you are experiencing another issue relating to the Flight-ready tag, this can be resolved by ordering a replacement part below.

When your Dyson Corrale™ is held closed, or in the locked position, there is an intended allowance of approximately 4mm of sideways movement in the arms. This is to avoid damage to the product.

This is normal and the machine is working as expected.

Normal use

This is normal and the machine is working as expected.

When completely closed, the front tips of the flexing plates will touch and there will be a gap of up to 1mm at the rear of the flexing plates.

Unlock your Dyson Corrale™ and close the plates together.

This is normal and the machine is working as expected.

Important

Please note, a white fast flashing on/off button signifies a battery issue. Should this occur you must not fly with the product, please contact Dyson immediately.

Battery light

The battery charging LED is located on the lower part of the Dyson Corrale™ straightener. The LED will be amber while charging and turn green when fully charged.

Reset the machine

Turn your straightener off and then back on again to reset.

Sleep mode

If your Dyson Corrale™ straightener is left unattended with the power on for longer than five minutes, the flexing plates will automatically switch off.

The Power button will flash red every 10 seconds during this time.

If you close your straightener without turning the power off, the Power button will flash every three seconds until you turn the power off. After five minutes, the machine will revert to the Sleep mode above.

The Power button will pulse until the selected temperature has been reached as it heats up or cools down.

The power button illuminates solid red when the selected temperature has been reached.

Check the OLED screen for an alert.

Please check whether your Flight-ready tag has two or four pins.

You can select your preferred temperature units (Centigrade or Fahrenheit).

Press and hold the Power and Temperature (+) buttons to change between units.

When your preferred temperature unit shows on the OLED screen, release the buttons.

Download important safety information and warranty terms and conditions.

Press the Temperature (+/−) control buttons to select the temperature that suits your hair type and styling preference.

Your straightener has three settings, to enable you to style at lower temperatures.

The temperature will appear on the OLED screen as it heats up or cools down and the Power button will pulse until the selected temperature has been reached.

Your dock can be used as a charging dock or a stand to store your Dyson Corrale™ straightener.

Push the two parts of the charging dock together until they click securely in place.

Connect the Magnetic 360° charging cable to the base of the charging dock.

Once assembled, your charging dock can be disassembled by pulling the support arm out of the base.

Changing temperature units

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

You can select your preferred temperature units (Centigrade or Fahrenheit).

Press and hold the Power and Temperature (+) buttons to change between units.

When your preferred temperature unit shows on the OLED screen, release the buttons.

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Before using your Dyson Corrale™ straightener for the first time, remove the Flight-ready tag from any packaging.

Insert the Flight-ready tag into your straightener.

Fully charge your straightener before first use.

For the best styling results, make sure your hair is dry and tangle-free.

Please check whether your Flight-ready tag has two or four pins.

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Insert the Flight-ready tag into your straightener.

Fully charge your straightener before first use.

For the best styling results, make sure your hair is dry and tangle-free.

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Your Dyson Corrale™ straightener is shipped in Flight-ready mode.

Before using your straightener for the first time, slide the unlock button up, then remove, rotate and replace the Flight-ready tag into the Home position, to connect the battery.

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

If your Dyson Corrale™ straightener is left unattended with the power on for longer than five minutes, the flexing plates will automatically switch off.

The Power button will flash red every 10 seconds during this time.

Press any button to reactivate your straightener.

The temperature will increase to the last setting used.

If your straightener is left unattended with the power on for a further five minutes, it will turn off completely.

Styling guides

Go to www.dyson.com/mycorrale for styling tips and guides.

When turning on

Slide the Lock button to open your straightener.

Press and hold the Power button until a battery icon appears on the OLED screen.

Press the Temperature (+) button to select the temperature you want.

The Power button will pulse red as your straightener heats up.

Your straightener is ready to use when the Power button illuminates red, a prompt sounds and a tick icon appears on the OLED screen.

When turning off

Press and hold the Power button until the OLED screen turns off.

Close your straightener and slide the safety lock button to close.

If you close your straightener without turning the power off, the Power button will flash every three seconds until you turn the power off. After five minutes the flexing plates will automatically start to cool down. After a further five minutes, your straightener will turn off completely.

To turn off your straightener, unlock, press and hold the Power button until the OLED display turns off.

User guide

Please open the PDF for the user guide.

User guide

Please open the PDF for the user guide.

Finding the machine serial number

The serial number can be found in the following locations:

On the front of the instruction manual.

On the box of the machine.

On the battery pack label.

Cleaning your straightener

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Turn off your Dyson Corrale™ straightener and leave to cool before cleaning.

Clean the flexing plates with a damp, lint-free cloth. Rub gently to remove any stubborn hair product residue.

Don't use chemicals or abrasive products as this may damage the surface of the flexing plates.