Cleaning the machine

The following areas should be checked and cleaned to maintain the machine's performance:

Clean the loop amplifier with a dry or damp cloth.

Clean the Main body with a dry cloth.

Clean the shroud with a dry cloth or soft brush.

Check that your machine has been connected

If you have previously connected your machine to the Dyson Link app, you should be able to see it on the app home screen. If you have multiple machines connected, you can switch between them using the burger menu in the top left of the home screen.

Connection unstable

Try moving the device and purifier closer to the router. If the Wi-Fi signal is poor your machine's connection may not be stable.

Software update required

Some Link app features may not be available if your machine is not up to date.

Please ensure auto-update is turned on. You can do this by going to your machine's settings.

This will ensure you automatically receive the latest features and your machine functions correctly.

It can take up to 24 hours for your machine to receive updates after it is enabled.

Offline

This message will show if your machine is switched off or unable to connect to the Dyson Cloud.

Turn off and unplug the machine.

Unplug the machine and leave it for 10 seconds.

Plug the machine in and switch it on.

Check your internet connection

Check that your Wi-Fi router or access point has an established internet connection. For the Link app to see your Dyson machine, your mobile device should also be connected to your home Wi-Fi or mobile broadband.

Connectivity disabled on purifier

If connectivity is disabled, press and hold your purifier's power button for 5 seconds. Once enabled, a solid white Wi-Fi symbol will display on your purifier. Repeat to toggle between enabled/disabled.

Enable auto-update

Please ensure auto-update is turned on. You can do this by going to your machine's settings through the settings icon.

This will make sure you automatically receive the latest features and your app functions correctly.

If auto-updates are already enabled, switch the machine off and unplug. Leave for 10 seconds, plug back in and switch on. Move your machine and device closer to the router.

Turn off and unplug

Please turn the machine off, unplug and leave for 10 seconds.

Move your machine and device closer to the router.

Slow response

The app will show an error if the connection has failed. Tap retry/continue to try connecting again. If the issue is resolved, continue to the next step.

Machine connected

Your machine is now connected to your Dyson Link app.

Please follow the rest of the steps to complete the set-up process.

Taking ownership

If this product has been connected before and you decide to take ownership, the previous owner will be notified and will no longer be able to use this machine with their Dyson Link app.

Where is the machine?

To personalise the machine and use with voice control services, select which room your machine is in.

Select location

Please select a location from the list shown on your device before submitting and confirming your selection.

Alternatively, if you want to choose a custom location, scroll to the bottom to edit it.

Purchase date

Enter the date of purchase. We'll need this for your guarantee.

It is recommended that you keep hold of your proof of purchase.

Auto update

Please ensure auto-update is turned on. You can do this by going to your machine's settings through the settings icon.

This will make sure you automatically receive the latest features and your app functions correctly.

If auto-updates are already enabled, switch the machine off and unplug. Leave for 10 seconds, plug back in and switch on. Move your machine and device closer to the router.

Set worldwide location

Set your location to display outdoor air quality information.

Setup complete

Your machine is now fully connected and setup.

Trouble connecting

Check your machine is plugged in and switched on.

Keep your device close to the machine and try again.

If the connection continues to fail, re-start the connection. Select 'Connecting your machine.' If this has already been tried, select 'Issue not resolved'

Dyson Link app

You'll need to have the Dyson Link app installed to connect to your machine.

Ensure Bluetooth and Wi-Fi are enabled on your device.

You have the option to create a new account or log in if you have previously created a Dyson account on the app or online. Select the appropriate option

Plug the machine in and switch it on.

Add machine

You can add a machine from the hamburger menu or from the main screen if no machines are registered. If bluetooth is not enabled, you will be prompted to enable it.

Location services

To scan for Wi-Fi networks, we'll need to access your device's location services. Allow this when prompted.

Select machine

Select your machine when it appears. The app will display its serial number.

Pairing

Hold your device next to your machine's display

Press the power button when prompted on your machine to activate pairing.

Once paired, continue to the next step.

Manual pairing

If you are still not able to pair the machine, follow the on screen prompts to manually pair.

You will need your machine's 8-digit code located on the machine behind the filter.

Enter your machine's code to continue.

Enter network details

Select your network from the list of available networks.

Enter the Wi-Fi passord for the chosen network.

Connection stage

You should see a confirming connection message. The connection progress is represented by purple dots at the top of the screen.

Network not found

If you are not able to see your network, you can select it using the prompts in the app.

Please ensure your machine is in range of your Wi-Fi and your network is working correctly.

Refresh the network list.

Unable to find machine

If you are not able to see your machine, you can select it using the prompts in the app.

Ensure Bluetooth and Wi-Fi are enabled on your device.

Plug the machine in and switch it on.

Keep your device close to the machine during this process.

Select machine

Select your machine when it appears. The app will display its serial number.

Two-factor authentication

Check that the email address shown on the login screen is correct. The code will be sent to the address shown.

The email may have incorrectly been marked as spam or junk. Please check any junk folders for the code email.

Please note that the authentication code will expire 5 minutes after being sent. Codes will also expire when a new one is sent.

If you enter the password or authentication code incorrectly more than four times, your account will be locked. It will be automatically unlocked after 30 minutes.

Dyson Link app

Download the latest version of the Dyson Link app from the app store on your phone. For users of Android phones, it can be downloaded from major Android app stores.

Minimum requirements:

• iOS 12
• Android 7.0 Nougat

Your My Dyson account

Once you have downloaded and updated the Dyson Link App, please login or register a My Dyson account.

To set up an account you will require a valid email address and password.

Switching Wi-Fi

Plug the machine in and switch it on.

Check that the Bluetooth and Wi-Fi are still enabled on your device.

Change your Wi-Fi network by going to your machine’s settings through the settings icon.

Select the network you want to connect to from the list of available networks.

Ensure your device remains close to the machine while switching networks.

Enter the Wi-Fi password to connect.

Historical data

With your machine selected, swipe up to view your air quality.

The following options are available.

• Daily or Weekly graph
• Switch days/weeks to view
• Ability to switch from showing;
  • Air Quality
  • PM2.5
  • PM10
  • VOC
  • NO2
  • Temperature
  • Humidity

More information is available by selecting the options above.

Machine controls

Your machine's controls are available through the home screen of the app.

You can control the following;

• Turn on/off
• Set the airflow speed
• Turn on and customise oscillation
• Set a timer
• Turn auto mode on/off
• Change airflow direction

Machine schedules

Schedules can be added or changed in your machine's settings.

Add events to set a schedule for when your machine should switch on and off. You can also set the following.

• Auto mode enabled/disabled
• Airflow speed
• Temperature target
• Oscillation
• Airflow direction
• Night mode enabled/disabled

Accessing the settings

To access your machine’s settings, select your machine from the hamburger menu and then select the settings menu icon.

Temperature unit setting

The temperature unit can be changed in your machine's settings.

The temperature unit can be changed between Celsius and Fahrenheit.

Continuous monitoring setting

Enabling/disabling continuous monitoring can be changed in your machine's settings.

Continuous monitoring allows your machine to collect environmental information. Once selected, this feature is active at all times.

Filter management

The filter life can be checked in your machine's settings.

Selecting filter management will show you how to replace your filter and allow you to reset filter life. Resetting filter life should only be done after you have replaced the filter.

Location setting

Your home location can be changed by selecting the appropriate time zone.

Select location from the list. You can also search for a location to filter the list.

Once a new location has been chosen, update to save.

Room name setting

The room name can be changed in your machine's settings.

Select room location from the available list or enter a custom name.

Once a new room name has been selected, follow the prompts in the app to change.

Switching machines

To switch between your machines, select the hamburger menu. A list of your machines will show on the left.

You can also swipe between your connected machines by swiping the sides of your screen. For Android users, screen gestures may need to be disabled for this feature to work.

Switching Wi-Fi

You can change to a different router or access point in your machine's settings.

Plug the machine in and switch it on.

Check that the Bluetooth and Wi-Fi are still enabled on your device.

Select the network you want to connect to from the list of available networks.

Ensure your device remains close to the machine while switching networks.

Enter the Wi-Fi password to connect.

When your purifier switches from front to rear airflow there may be a clicking sound as the motor adjusts direction.

This is a normal sound for the purifier to make and is not an indicator of anything wrong with your machine.

Check base

Check around the base of the machine for any debris or obstructions.

Continuous monitoring

The continuous monitoring option is used for air quality, temperature and humidity data to be relayed to the machine and app at all times, even when you have turned the purifier off. The sensors have small fans that maintain airflow for continuous monitoring, but this should not cause any audible noise interference.

There may be instances when the display shows green, indicating high air quality, but the fan speed is still high. This is due to the machine constantly seeking to maintain a good air quality, and in scenarios such as rooms with leaky windows, the machine must work harder to maintain a good air quality.

This will only happen when the machine is set on auto. To turn off Auto mode, please select Manual mode, either using the remote control or on the app.

Please check the following on the app:

Swipe up to reveal the setting tab and tap to open options.

Swipe down to find the continuous monitoring option and tap to open.

Turn OFF the 'Collect data when in standby' option. (The icon will turn grey when turned off). Save the change by pressing 'Done' at the top right of the page.

Continuous monitoring can now also be turned on/off by pressing the 'Auto' button on the remote control for five seconds.

Retest the machine.

Restart the machine

Unplug the machine and leave it for 10 seconds.

Ensure the power cord is plugged into the centre of the base.

Plug the machine back in and retest.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds.

The shrouds will release with the glass HEPA filters attached.

Plug the machine back in and retest.

Turn off power and unplug the machine.

To remove the carbon filters: press the tabs on both sides of the filters.

Plug the machine back in and retest.

Remote controls

Ensure correct button on remote is being pressed to adjust the airflow.

Test the other remote buttons

Test the other buttons on the remote.

On/Off

Oscillation

Automatic mode

Sleep timer

Night mode

Test airspeed

Test airspeed change using the Dyson link app.

Changing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.

Check and clean loop amplifier

The following areas should be checked and cleaned to maintain the machine's performance.

Clean the loop amplifier with a dry or damp cloth.

Ensure that the narrow opening is free of obstructions.

Check and clean Main body

Clean the shroud of the Main body with a dry cloth.

Use a soft brush to clear any blockages from the holes.

Check airflow direction

This product has dual airflow direction options. Please ensure you have directed the airflow to come out the front of the machine before beginning these checks.

You can do this by pressing the airflow direction button on the remote control.

Check the electrics

Check that the household electrics are on.

Check the plug and power cord for signs of damage.

Try the machine in a different plug socket.

Ensure the cable is firmly plugged into the back of the machine.

Check using the remote control

Press the oscillation button on the remote.

If the using the buttons on the remote doesn't work, try changing the batteries.

Check with the Dyson Link app

Try using the Dyson Link app to control the oscillation.

Test the remote control

Ensure the correct button on the remote is being pressed.

Point the remote directly at the front of the machine while pressing the button.

Test the other remote buttons

Airflow speed

On/Off

Press the ON/OFF button on the Main body of the machine.

Point the remote directly at the front of the machine while pressing the button.

Open the Dyson Link app.

Under your Purifier, open the remote on the app and press the ON/OFF button.

Open the Dyson Link app.

Under your Purifier, open the remote on the app and press the ON/OFF button.

Check and clean machine

The following areas should be checked and cleaned to maintain the machine's performance.

Clean loop amplifier with a dry or damp cloth.

Clean the Main body with a dry cloth.

Clean inlet grille with a dry cloth or soft brush.

Your filter may need replacing.

Check filter life within the app, on the display screen, or for excessive build up of dust within the inlet.

When the appliance detects that the nonwashable glass HEPA filters need replacing the display on the appliance will show an empty bar.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds.

The shrouds will release with the glass HEPA filters attached.

Empty the glass HEPA filters directly into the bin by pushing in both the purple tabs on the shrouds. Dispose of used filter units in accordance with local regulations.

Push the new glass HEPA filters into the shrouds until secure. Push the shrouds until they click back into position in the base.

Plug the appliance in to the mains electricity supply and switch on.

Press and hold the Night mode button on the remote control. The display on the appliance will countdown from five, finishing with the default screen. The glass HEPA filter level will be reset and the appliance is ready to use.

When the appliance detects that the non-washable carbon filters need replacing the display on the appliance will show an empty bar.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds. The shrouds will release with the glass HEPA filters attached.

To remove the carbon filters: press the tabs on both sides of the filters.

Dispose of the carbon filters in the bin. Dispose of used filter units in accordance with local regulations.

Push the new carbon filters onto the base until secure.

Push the shrouds until they click back into position in the base.

Plug the appliance in to the mains electricity supply and switch on.

Press and hold the Oscillation button on the remote control. The display on the appliance will countdown from five, finishing with the default screen. The carbon filter level will be reset and the appliance is ready to use.

Please ensure you have the most up to date software downloaded before beginning any checks. We strongly recommended enabling auto-updates in your Dyson Link app settings, to allow the most up to date software to be installed as soon as it is available.

Check machine base

Ensure all the feet are attached to the base of the machine.

Place the purifier on a flat, non-slip surface.

Check remote control

Ensure correct button on remote is being pressed.

Point the remote directly at the front of the machine while pressing the button.

Test the other remote buttons

Airflow speed

Airflow direction

Changing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.

Check with the Dyson Link app

Open the app and set the machine to oscillate.

If you do not have the Dyson Link app set up, please select 'No' as the next option.

Check remote control

Ensure correct button on remote is being pressed.

Point the remote directly at the front of the machine while pressing the button.

Check other buttons

Test the other buttons on the remote.

Airflow speed

Airflow direction

Changing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.

Check with the Dyson Link app

Open the app and set the machine to oscillate.

Point the remote at the base of the purifier and test the controls.

Check if the Dyson Link app is working.

Changing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.

Fault

Reset the machine.

Unplug the machine and leave it for 10 seconds.

Ensure the power cord is plugged into the centre of the base.

Plug the machine back in and retest.

Restart the machine

Switch off and unplug the machine.

Ensure all outside doors and windows are closed.

Vacuum the two sensor slots to the left of the LCD screen with a Dyson brush attachment.

Plug in and test the machine.

Switch off and unplug the machine.

Move the machine to another room.

Plug in and test the machine.

Night mode is not working

When in Night mode, your machine will automatically sense the ambient light level and adjust the resting screen brightness accordingly.

If the room is bright, (for example, the lights are on), the screen's display will be set to minimum brightness. If the room is dark (lights off) the screen is turned off.

In both scenarios, when the machine is interacted with, the screen brightness will uplift.

The display will not stay on my selected screen

The interface is designed to stay on the screen you select. Please ensure the remote is not being accidentally pressed.

My display is reading green but the fan is working at high speed

There may be times when the display is showing green but the fan speed is still high.

This is due to the machine always trying to maintain high air quality. For example, in a room with leaky windows, the machine has to work harder via a higher Fan speed to maintain a high air quality.

If you want the fan to be quieter, you can choose to change the airflow direction to face backwards, or turn the machine to manual mode and lower the airspeed.

My readings are showing in different colours

The colour of the numbers and readings on the display are linked to the air quality of the respective category.

Green denotes a high air quality, with low pollutants, and red, low air quality with a high amount of pollutants.

Different categories can have different levels of pollutants at the same time, and will therefore display in different colours.

The first time your purifier is turned on, the gas sensors will perform a self-calibration which takes one hour after which time they will work normally.

If the power cuts out within the hour, the initialisation period will continue from where it left off.

If your machine is new out the box and has not been turned on for over an hour, please allow a full hour to complete, with your purifier plugged into a secure power source.

Once the full hour has elapsed, turn the machine off and then on again, either with the main power button on the machine, or the remote control.

Complete manual reset

If your purifier has been plugged into a stable power source for over one hour, and the VOC and/or NO2 screens still do not show, please unplug your machine from the wall, leave for one minute, plug back in, and then turn on using either the main power button, or the button on the remote.

When the appliance detects that the non washable glass HEPA filters need replacing the display on the appliance will show an empty bar.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds.

The shrouds will release with the glass HEPA filters attached.

Empty the glass HEPA filters directly into the bin by pushing in both the purple tabs on the shrouds. Dispose of used filter units in accordance with local regulations.

Push the new glass HEPA filters into the shrouds until secure. Push the shrouds until they click back into position in the base.

Push the new glass HEPA filters into the shrouds until secure. Push the shrouds until they click back into position in the base.

Press and hold the Night mode button on the remote control. The display on the appliance will countdown from five, finishing with the default screen. The glass HEPA filter level will be reset and the appliance is ready to use.

When the appliance detects that the non-washable carbon filters need replacing the display on the appliance will show an empty bar.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds. The shrouds will release with the glass HEPA filters attached.

To remove the carbon filters: press the tabs on both sides of the filters.

Dispose of the carbon filters in the bin. Dispose of used filter units in accordance with local regulations.

Push the new carbon filters onto the base until secure.

Push the shrouds until they click back into position in the base.

Plug the appliance in to the mains electricity supply and switch on.

Press and hold the Oscillation button on the remote control. The display on the appliance will countdown from five, finishing with the default screen. The carbon filter level will be reset and the appliance is ready to use.

Please open the PDF for the user guide.

Quick start guide

Please follow the steps in the video.

Find the text version of the step-by-step guide instead, under "Is there anything else we can help you with?"

Use both hands to lift the appliance out of the box, taking care to hold by the base of the appliance only. Do not lift out by the amplifier loop.

Take the carbon filters out of the box and remove the protective packaging.

Attach both carbon filters to the appliance.

Remove the glass HEPA filters from their protective packaging and push into the shrouds until secure.

Position the shrouds onto the base and push gently until they click securely into place. Place the remote control on the top of the appliance with the buttons facing down. Plug in and switch ON.

The remote control can be magnetically attached to the top of the loop.

Using the remote control

To operate, point the remote control toward the front of the base.

On/Off

Press the power ON/OFF button on the appliance or remote control to stop the purifier. The appliance will continue to monitor the air quality.

Airflow speed

Press the Airflow speed button to increase and decrease the airflow speed.

Oscillation On/Off

Press the Oscillation button to scroll through the options from 0 to 350.

Customise your oscillation settings in the Dyson Link app and it will appear as an option as you scroll through.

Information menu

Scroll through the options to monitor the performance of your appliance.

The menu will also allow you to access information about the pollutants in the air and the temperature and humidity levels.

When a particular type of pollutant causes air quality to decrease, the symbol for that pollutant will show in the display.

Auto mode

When Auto mode is selected the onboard sensors will intelligently adjust the settings of the appliance according to the quality of air.

The appliance will pause once the sensors detect that the target air quality level has been reached.

The sensors will continue to monitor the air quality, switching the appliance back on when air quality levels have dropped.

Customise your Auto mode and air quality settings in the Dyson Link app.

Airflow direction

Air will be purified continuously, whether the air is set to flow from the front or the back.

For purification and cool airflow, select the airflow direction to the front.

For purification without cool airflow from the front, select the airflow direction to the back.

Night mode

Night mode will dim the display and the appliance will run more quietly, making it ideal for use while sleeping. If Auto mode has been set, Night mode will reduce airflow speeds to range from 1 to 4. You can manually change the airflow from 1-10. Customise your Night mode settings in the Dyson Link app.

Auto mode

Auto mode adjusts the speed according to the air quality in the room.

When Auto mode is enabled (indicated by an A symbol in the bottom left corner of the display), the on-board sensors will intelligently adjust the speed of the purifier according to the air quality.

Increasing speed for poor air quality.

Reducing speed as the air quality improves.

If the air quality target is met, the air quality graph will show green. The air quality will continue to be monitored, with the fan running on a low speed in the background.

If the air quality worsens the air quality graph will show red and the purifier will automatically restart cleaning the room.

There may be times when the display shows green, but the fan speed is still high.

This is due to the machine constantly maintaining a high air quality.

If there is a factor in the environment such as leaky windows, the machine must work harder to sustain a high air quality.

Turning Auto mode on/off

Tap the remote icon on the bottom right corner of the home page.

Tap the power icon at the top of the menu and tap AUTO to select.

When Auto mode is enabled, 'Auto' is written at the top of the display.

To turn Auto mode off, press the same button.

Press Auto button

Press the 'Auto' button on the top right corner of the remote control.

To turn Auto mode off press the same button.

Manual mode

Airflow can be set manually by the airflow buttons on the remote.

You can choose a setting from 1 (low flow of air) through to 10 (high flow of air), and the machine home screen will show the fan speed when in manual mode

Auto mode

Auto mode adjusts the speed according to the air quality in the room. When Auto mode is enabled (indicated by a graph on the home screen showing the air quality, with ‘AUTO’ at the top), the on-board sensors will intelligently adjust the speed of the purifier according to the air quality. Increasing speed for poor air quality.

Reducing speed as the air quality improves.

If the air quality target is met, the air quality graph will show green. The air quality will continue to be monitored, with the fan running on a low speed in the background.

If the air quality worsens the air quality graph will show red and the purifier will automatically restart cleaning the room.

There may be times when the display shows green, but the fan speed is still high.

This is due to the machine constantly maintaining a high air quality.

If there is a factor in the environment such as leaky windows, the machine must work harder to sustain a high air quality.

Indoor air quality - 12 seconds

Monitor the current air quality with a graph showing the last 12 seconds of data.

Indoor air quality - 24 hours

Monitor the air quality with a graph showing the last 24 hours of data.

Particulate matter (PM2.5)

Microscopic particles up to 2.5 microns in size, suspended in the air we breathe. These include smoke, bacteria and allergens.

Particulate matter (PM10)

Larger microscopic particles up to 10 microns in size, suspended in the air we breathe. These include dust, mould and pollen.

Nitrogen dioxide and other oxidising gases

These potentially harmful gases are released into the air by combustion, for example the burning gas when cooking and in vehicle exhaust emissions.

Volatile organic compounds

VOC’s are typically odours that may be potentially harmful. These can be found in cleaning products, paints and new furnishings.

Indoor temperature

Monitor the ambient temperature to help maintain a comfortable environment.

Indoor humidity

The amount of water vapour in the air, shown as a percentage of the maximum possible humidity at the current temperature.

Filters

The amount of pollution captured by the filters is shown in the display. When the filter is full, the display will flash to remind you which filter needs changing.

WiFi

The current status of connection to the WiFi network.

Use both hands to lift the appliance out of the box, taking care to hold by the base of the appliance only. Do not lift out by the loop amplifier.

Take the carbon filters out of the box and remove the protective packaging.

Attach both carbon filters to the appliance.

Remove the glass HEPA filters from their protective packaging and push into the shrouds until secure.

Position the shrouds onto the base and push gently until they click securely into place. Place the remote control on the top of the appliance with the buttons facing down. Plug in and switch ON.

The remote control can be magnetically attached to the top of the loop.

Finding the machine serial number

The serial number and WiFi information can be found in the following locations:

On the front of the user guide.

On a removable sticker on the front of the purifier.

On your purifier, located underneath the filter.

Information menu

Scroll through the options to monitor the performance of your appliance.

The menu will also allow you to access information about the pollutants in the air and the temperature and humidity levels.

When a particular type of pollutant causes air quality to decrease, the symbol for that pollutant will show in the display.

Indoor air quality - 12 seconds

Monitor the current air quality with a graph showing the last 12 seconds of data.

Indoor air quality - 24 hours

Monitor the air quality with a graph showing the last 24 hours of data.

Particulate matter (PM2.5)

Microscopic particles up to 2.5 microns in size, suspended in the air we breathe.

These include smoke, bacteria and allergens.

Particulate matter (PM10)

Larger microscopic particles up to 10 microns in size, suspended in the air we breathe. These include dust, mould and pollen.

Nitrogen dioxide and other oxidising gases

These potentially harmful gases are released into the air by combustion, for example the burning gas when cooking and in vehicle exhaust emissions.

Volatile organic compounds

VOC’s are typically odours that may be potentially harmful.

These can be found in cleaning products, paints and new furnishings.

Indoor temperature

Monitor the ambient temperature to help maintain a comfortable environment.

Indoor humidity

The amount of water vapour in the air, shown as a percentage of the maximum possible humidity at the current temperature.

Filters

The amount of pollution captured by the filters is shown in the display. When the filter is full, the display will flash to remind you which filter needs changing.

WiFi

The current status of the connection to the WiFi network.

Removing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.