Cleaning the machine

The following areas should be checked and cleaned to maintain the machine's performance:

Clean the loop amplifier with a dry or damp cloth.

Clean the Main body with a dry cloth.

Clean the shroud with a dry cloth or soft brush.

When your purifier switches from front to rear airflow there may be a clicking sound as the motor adjusts direction.

This is a normal sound for the purifier to make and is not an indicator of anything wrong with your machine.

Check base

Check around the base of the machine for any debris or obstructions.

Continuous monitoring

The continuous monitoring option is used for air quality, temperature and humidity data to be relayed to the machine and app at all times, even when you have turned the purifier off. The sensors have small fans that maintain airflow for continuous monitoring, but this should not cause any audible noise interference.

There may be instances when the display shows green, indicating high air quality, but the fan speed is still high. This is due to the machine constantly seeking to maintain a good air quality, and in scenarios such as rooms with leaky windows, the machine must work harder to maintain a good air quality.

This will only happen when the machine is set on auto. To turn off Auto mode, please select Manual mode, either using the remote control or on the app.

Please check the following on the app:

Swipe up to reveal the setting tab and tap to open options.

Swipe down to find the continuous monitoring option and tap to open.

Turn OFF the 'Collect data when in standby' option. (The icon will turn grey when turned off). Save the change by pressing 'Done' at the top right of the page.

Continuous monitoring can now also be turned on/off by pressing the 'Auto' button on the remote control for five seconds.

Retest the machine.

Restart the machine

Unplug the machine and leave it for 10 seconds.

Ensure the power cord is plugged into the centre of the base.

Plug the machine back in and retest.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds.

The shrouds will release with the glass HEPA filters attached.

Plug the machine back in and retest.

When not in use, unplug from the mains electricity supply.

To remove the carbon filters: press the tabs on both sides of the filters.

Plug the machine back in and retest.

Ensure correct button on remote is being pressed to adjust the airflow.

Test the other remote buttons

Test the other buttons on the remote.

On/Off

Oscillation

Automatic mode

Night mode

Point the remote directly at the front of the machine while pressing the button.

Test airspeed change using the Dyson link app.

Changing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.

Check and clean loop amplifier

The following areas should be checked and cleaned to maintain the machine's performance.

Clean the loop amplifier with a dry or damp cloth.

Ensure that the narrow opening is free of obstructions.

Check and clean Main body

Clean the shroud of the Main body with a dry cloth.

Use a soft brush to clear any blockages from the holes.

Check airflow direction

This product has dual airflow direction options. Please ensure you have directed the airflow to come out the front of the machine before beginning these checks.

You can do this by pressing the airflow direction button on the remote control.

Check the electrics

Check that the household electrics are on.

Check the plug and power cord for signs of damage.

Try the machine in a different plug socket.

Ensure the cable is firmly plugged into the back of the machine.

Check using the remote control

Press the oscillation button on the remote.

If the using the buttons on the remote doesn't work, try changing the batteries.

Check with the Dyson Link app

Try using the Dyson Link app to control the oscillation.

Test the remote control

Ensure the correct button on the remote is being pressed.

Point the remote directly at the front of the machine while pressing the button.

Test the other remote buttons

Airflow speed

On/Off

Press the ON/OFF button on the Main body of the machine.

Point the remote directly at the front of the machine while pressing the button.

Open the Dyson Link app.

Under your Purifier, open the remote on the app and press the ON/OFF button.

Open the Dyson Link app.

Under your Purifier, open the remote on the app and press the ON/OFF button.

Check and clean machine

The following areas should be checked and cleaned to maintain the machine's performance.

Clean loop amplifier with a dry or damp cloth.

Clean the Main body with a dry cloth.

Clean inlet grille with a dry cloth or soft brush.

Your filter may need replacing.

Check filter life within the app, on the display screen, or for excessive build up of dust within the inlet.

When the appliance detects that the nonwashable glass HEPA filters need replacing the display on the appliance will show an empty bar.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds.

The shrouds will release with the glass HEPA filters attached.

Empty the glass HEPA filters directly into the bin by pushing in both the purple tabs on the shrouds. Dispose of used filter units in accordance with local regulations.

Push the new glass HEPA filters into the shrouds until secure. Push the shrouds until they click back into position in the base.

Plug the appliance in to the mains electricity supply and switch on.

Press and hold the Night mode button on the remote control. The display on the appliance will countdown from five, finishing with the default screen. The glass HEPA filter level will be reset and the appliance is ready to use.

When the appliance detects that the non-washable carbon filters need replacing the display on the appliance will show an empty bar.

Unplug the appliance from the mains electricity supply. Slide the buttons down on either side of the shrouds. The shrouds will release with the glass HEPA filters attached.

To remove the carbon filters: press the tabs on both sides of the filters.

Dispose of the carbon filters in the bin. Dispose of used filter units in accordance with local regulations.

Push the new carbon filters onto the base until secure.

Push the shrouds until they click back into position in the base.

Plug the appliance in to the mains electricity supply and switch on.

Press and hold the Oscillation button on the remote control. The display on the appliance will countdown from five, finishing with the default screen. The carbon filter level will be reset and the appliance is ready to use.

Check that your machine has been connected

If you have previously connected your machine to the Dyson Link app, you should be able to see it on the app home screen. If you have multiple machines connected, you can switch between them using the burger menu in the top left of the home screen.

Two-factor authentication

Check that the email address shown on the login screen is correct. The code will be sent to the address shown.

The email may have incorrectly been marked as spam or junk. Please check any junk folders for the code email.

Please note that the authentication code will expire 5 minutes after being sent. Codes will also expire when a new one is sent.

If you enter the password or authentication code incorrectly more than four times, your account will be locked. It will be automatically unlocked after 30 minutes.

Unable to find machine

If you are not able to see your machine, you can select it using the prompts in the app.

Ensure Bluetooth and Wi-Fi are enabled on your device.

Plug the machine in and switch it on.

Keep your device close to the machine during this process.

Select machine

Select your machine when it appears. The app will display its serial number.

Pairing

Hold your device next to your machine's display

Press the power button when prompted on your machine to activate pairing.

Once paired, continue to the next step.

Manual pairing

If you are still not able to pair the machine, follow the on screen prompts to manually pair.

You will need your machine's 8-digit code located on the machine behind the filter.

Enter your machine's code to continue.

Enter network details

Select your network from the list of available networks.

Enter the Wi-Fi passord for the chosen network.

Network not found

If you are not able to see your network, you can select it using the prompts in the app.

Please ensure your machine is in range of your Wi-Fi and your network is working correctly.

Refresh the network list.

Connection stage

You should see a confirming connection message. The connection progress is represented by purple dots at the top of the screen.

Machine connected

Your machine is now connected to your Dyson Link app.

Please follow the rest of the steps to complete the set-up process.

Taking ownership

If this product has been connected before and you decide to take ownership, the previous owner will be notified and will no longer be able to use this machine with their Dyson Link app.

Where is the machine?

To personalise the machine and use with voice control services, select which room your machine is in.

Select location

Please select a location from the list shown on your device before submitting and confirming your selection.

Alternatively, if you want to choose a custom location, scroll to the bottom to edit it.

Purchase date

Enter the date of purchase. We'll need this for your guarantee.

It is recommended that you keep hold of your proof of purchase.

Auto update

Please ensure auto-update is turned on. You can do this by going to your machine's settings through the settings icon.

This will make sure you automatically receive the latest features and your app functions correctly.

If auto-updates are already enabled, switch the machine off and unplug. Leave for 10 seconds, plug back in and switch on. Move your machine and device closer to the router.

Set worldwide location

Set your location to display outdoor air quality information.

Setup complete

Your machine is now fully connected and setup.

Slow response

The app will show an error if the connection has failed. Tap retry/continue to try connecting again. If the issue is resolved, continue to the next step.

Trouble connecting

Check your machine is plugged in and switched on.

Keep your device close to the machine and try again.

If the connection continues to fail, re-start the connection. Select 'Connecting your machine.' If this has already been tried, select 'Issue not resolved'

Dyson Link app

You'll need to have the Dyson Link app installed to connect to your machine.

Ensure Bluetooth and Wi-Fi are enabled on your device.

You have the option to create a new account or log in if you have previously created a Dyson account on the app or online. Select the appropriate option

Plug the machine in and switch it on.

Dyson Link app

Download the latest version of the Dyson Link app from the app store on your phone. For users of Android phones, it can be downloaded from major Android app stores.

Minimum requirements:

• iOS 12
• Android 7.0 Nougat

Your My Dyson account

Once you have downloaded and updated the Dyson Link App, please login or register a My Dyson account.

To set up an account you will require a valid email address and password.

Add machine

You can add a machine from the hamburger menu or from the main screen if no machines are registered. If bluetooth is not enabled, you will be prompted to enable it.

Location services

To scan for Wi-Fi networks, we'll need to access your device's location services. Allow this when prompted.

Select machine

Select your machine when it appears. The app will display its serial number.

Password reset

After changing the password on your Dyson account, you'll need to wait 30 minutes before logging back in.

If you enter the password or authentication code incorrectly more than four times, your account will be locked. It will be automatically unlocked after 30 minutes.

Dyson Link app

You'll need to have the Dyson Link app installed to connect to your machine.

Ensure Bluetooth and Wi-Fi are enabled on your device.

You have the option to create a new account or log in if you have previously created a Dyson account on the app or online. Select the appropriate option.

Plug the machine in and switch it on.

Dyson Link app

Download the latest version of the Dyson Link app from the app store on your phone. For users of Android phones, it can be downloaded from major Android app stores.

Minimum requirements:

• iOS 12
• Android 7.0 Nougat

Your My Dyson account

Once you have downloaded and updated the Dyson Link App, please login or register a My Dyson account.

To set up an account you will require a valid email address and password.

Enable auto-update

Please ensure auto-update is turned on. You can do this by going to your machine's settings through the settings icon.

This will make sure you automatically receive the latest features and your app functions correctly.

If auto-updates are already enabled, switch the machine off and unplug. Leave for 10 seconds, plug back in and switch on. Move your machine and device closer to the router.

Software update required

Some Link app features may not be available if your machine is not up to date.

Please ensure auto-update is turned on. You can do this by going to your machine's settings.

This will ensure you automatically receive the latest features and your machine functions correctly.

It can take up to 24 hours for your machine to receive updates after it is enabled.

Offline

This message will show if your machine is switched off or unable to connect to the Dyson Cloud.

Turn off and unplug

Please turn the machine off, unplug and leave it for 10 seconds.

Plug the machine in and switch it on.

Check your internet connection

Check that your Wi-Fi router or access point has an established internet connection. For the Link app to see your Dyson machine, your mobile device should also be connected to your home Wi-Fi or mobile broadband.

Connectivity disabled on purifier

If connectivity is disabled, press and hold your purifier's power button for 5 seconds. Once enabled, a solid white Wi-Fi symbol will display on your purifier. Repeat to toggle between enabled/disabled.

Turn off and unplug

Please turn the machine off, unplug and leave for 10 seconds.

Move your machine and device closer to the router.

Connection unstable

Try moving the device and purifier closer to the router. If the Wi-Fi signal is poor your machine's connection may not be stable.

Switching Wi-Fi

Plug the machine in and switch it on.

Check that the Bluetooth and Wi-Fi are still enabled on your device.

Change your Wi-Fi network by going to your machine’s settings through the settings icon.

Select the network you want to connect to from the list of available networks.

Ensure your device remains close to the machine while switching networks.

Enter the Wi-Fi password to connect.

Historical data

With your machine selected, swipe up to view your air quality.

The following options are available.

• Daily or Weekly graph
• Switch days/weeks to view
• Ability to switch from showing;
  • Air Quality
  • PM2.5
  • PM10
  • VOC
  • NO2
  • Temperature
  • Humidity

More information is available by selecting the options above.

Machine controls

Your machine's controls are available through the home screen of the app.

You can control the following;

• Turn on/off
• Set the airflow speed
• Turn on and customise oscillation
• Set a timer
• Turn auto mode on/off
• Change airflow direction

Machine schedules

Schedules can be added or changed in your machine's settings.

Add events to set a schedule for when your machine should switch on and off. You can also set the following.

• Auto mode enabled/disabled
• Airflow speed
• Temperature target
• Oscillation
• Airflow direction
• Night mode enabled/disabled

Accessing the settings

To access your machine’s settings, select your machine from the hamburger menu and then select the settings menu icon.

Temperature unit setting

The temperature unit can be changed in your machine's settings.

The temperature unit can be changed between Celsius and Fahrenheit.

Continuous monitoring setting

Enabling/disabling continuous monitoring can be changed in your machine's settings.

Continuous monitoring allows your machine to collect environmental information. Once selected, this feature is active at all times.

Location setting

Your home location can be changed by selecting the appropriate time zone.

Select location from the list. You can also search for a location to filter the list.

Once a new location has been chosen, update to save.

Room name setting

The room name can be changed in your machine's settings.

Select room location from the available list or enter a custom name.

Once a new room name has been selected, follow the prompts in the app to change.

Filter management

The filter life can be checked in your machine's settings.

Selecting filter management will show you how to replace your filter and allow you to reset filter life. Resetting filter life should only be done after you have replaced the filter.

Switching machines

To switch between your machines, select the hamburger menu. A list of your machines will show on the left.

You can also swipe between your connected machines by swiping the sides of your screen. For Android users, screen gestures may need to be disabled for this feature to work.

Switching Wi-Fi

You can change to a different router or access point in your machine's settings.

Plug the machine in and switch it on.

Check that the Bluetooth and Wi-Fi are still enabled on your device.

Select the network you want to connect to from the list of available networks.

Ensure your device remains close to the machine while switching networks.

Enter the Wi-Fi password to connect.

Siri will need to be enabled in your device’s Settings, to use Siri Shortcuts with the Dyson Link app.

Open Settings on your phone or tablet, then select ‘Siri & Search’. Next, to enable Siri, switch on ‘Press home for Siri’.

Before you can use Siri Shortcuts, you must first add your connected machine to the Dyson Link app.

To create a Siri Shortcut, tap the cog on the top right-hand corner of your home screen and select ‘Voice control’ and then ‘Siri’. Then select ‘Add new shortcut’. Next, choose the required settings and press the ‘Add to Siri’ button.

So that Siri can tell the Dyson Link app to run your shortcut, a personalised phrase will need to be recorded. We suggest that each phrase is unique and it’s recognisable.

For example, if you’ve selected Cooling mode and Night mode, this could be named “Bed time” or a heating specific setting could be named “I’m cold”.

Please note, generic phrases already programmed into Siri can’t be used. An example of this is “Good Morning”.

A list of all personalised phrases will be stored on the ‘Your Siri Shortcuts’ screen for each machine.

To view this, simply tap the cog on the top right-hand corner of the relevant machine’s home screen and select ‘Voice control’ and then ‘Siri’.

Next, select the relevant Siri Shortcut. From here, you can re-record the phrase or deleted the shortcut.

With Siri Shortcuts, you can control your air treatment machine(s) using your voice. You can create, edit and delete your own personalised commands, which can be activated through your mobile or tablet.

Each Siri Shortcut is unique to the machine it was created on and cannot be applied across multiple machines.

You’ll need to create different Siri Shortcuts for each machine and a new personalised phrase will need to be recorded.

Should a personalised phrase be recorded across multiple machines, Siri will display these on your device as selectable options, along with a machine identifier.

If you have multiple machines using the Siri Shortcut feature, we recommend making each phrase unique. For example, if one machine is located in the kitchen and another is in the bedroom, include these locations in the phrase.

Siri Shortcuts can be used in any region where Apple supports Siri. To see if this is supported in your region, please visit the Apple website.

You can activate Siri Shortcuts on the Dyson Link app in one of two ways:

1. Simply say, “Hey Siri”, followed by the pre-recorded personalised phrase.*
2. By pressing your mobile or tablet’s ‘Home’ button to activate Siri, and then saying the pre-recorded personalised phrase when prompted.

Either way, you’ll need to be logged into the Dyson Link app.

*This option will needs Siri to be enabled in your phone or tablet’s Siri settings.

Siri Shortcuts is available on iOS 12 or later.

Enabling the Dyson skill

Using the Alexa App on your mobile device or the Amazon website, search for "Dyson Skill". Once it appears, select the Dyson Skill and enable it.

You will be prompted to log in to your Dyson account. You should use the account you connected your machine with via the Dyson Link app.

Once you have logged in, follow the on-screen instructions to link Alexa to your Dyson machines.

How does Alexa identify my machine?

Alexa identifies Dyson machines using their room name. The room name is set when you first connect your machine with the Dyson Link app and can be changed using the Link app as well. A list of preset room names are available in the Dyson Link app, such as 'Bedroom' or 'Kitchen'.

For convenience, you can also rename your machine using the Alexa app. However, this does not affect the room name in the Dyson Link app or how you control your machine with voice commands.

To control a specific Dyson machine using voice commands, you can either directly name the machine in your first command or wait for Alexa to ask which machine you are referring to.

If you ask "Alexa, enable auto mode on Bedroom.", Alexa will identify the 'Bedroom' machine and enable the auto mode for it.

If you ask "Alexa, enable auto mode.", Alexa will ask which machine you want to enable the auto mode for.

Disabling the Dyson Skill

You can disconnect Alexa from your Dyson account and machines by disabling the Dyson skill. You can disable the Dyson Skill using the Alexa app or Amazon website.

Please note that you will need to log in to your Dyson account again if you choose to re-enable the skill.

Check if Alexa heard you

If Alexa did not respond to your most recent request, what you said may not have been recognised as a question or command. To make sure Alexa recognises your request, speak clearly and ensure you are close enough to your Echo device for her to hear you.

To check if Alexa is able to hear you, ask "Alexa, did you hear me?".

Check your smart home device

First, make sure:

1. Your Google Nest or Google Home speaker or display is powered on and plugged into a wall outlet
2. The microphone isn't muted
   • For Google Home: on the back of the device, touch the microphone mute button. Your Assistant will say whether the microphone is muted.
   • For Google Nest Mini (2nd gen) and Google Home Mini (1st gen): on the side of the device, toggle the mic switch. Your Assistant will say whether the microphone is muted.
   • For Google Nest Audio: on the back of the device, next to the power cord, toggle the mic switch. Your Assistant will say whether the microphone is muted.
   • For Google Nest displays: on the back of your display, use the switch to turn on the microphone. Your Assistant will say whether the microphone is muted.
3. The LED dots on top of your speaker or display spins or blinks when you say “Ok Google” or "Hey Google."
4. If your Assistant answers other questions, try to ask the unanswered question in a different way.

General troubleshooting

If you've checked off all of the steps above and your Assistant still doesn't provide an answer, try one of the steps below and ask your question again. If you still don't get an answer, move to the next step.

Reset your password

If you are unable to log in and link your Dyson account, you may need to reset your password. Select the forgotten password link on the log in screen to be taken through the reset process.

If the password has recently been changed, a 30 minutes period will need to pass before you are able to log back into the Dyson Link app account.

Multiple failures logging into the account (4 or more) will result in the account becoming locked. The account will remain locked for a 30 minute period.

Ask Alexa what she heard

Alexa may have misheard you or misinterpreted something you said as a request. To understand why Alexa just did something, say "Alexa, why did you do that?" or "Alexa, what did you do?".

You can also ask Alexa to read back your most recent request by saying "Alexa, what's the last thing you heard?" or "Alexa, what did you hear?".

You can also view Alexa's activity in the Alexa app on your mobile device. The activity log shows utterances that Alexa heard, responses she gave and actions she took.

Check for device or setup issues

In order for Alexa to discover your Dyson machine, it must be connected via the Dyson Link app and the Dyson Skill needs to be enabled.

If your machine has not been connected with the Dyson Link app, select the connection journey option to go through these steps.

Your Dyson machine and your Echo device should both be connected to the same Wi-Fi network to allow for discovery.

Check your machine

Turn off your Dyson machine at the wall for 10 seconds. Then turn it back on.

Do the same with your Echo device.

Check that your machine is online by viewing it in the Dyson Link app.

Check the Dyson skill

In the Alexa app on your mobile device, disable and then re-enable the Dyson Skill.

You will need to log into your Dyson account again after re-enabling the the Dyson Skill.

What are some of the things I can do with Alexa?

There are different kinds of directives that users can use to interact with Alexa. Here are some examples:

Turn settings on and off

• "Alexa, turn on my purifier."
• "Alexa, turn on night mode."
• "Alexa, turn off humidification."

Control number settings

• "Alexa, set the bedroom fan speed to 7."
• "Alexa, turn up the bedroom fan speed."
• "Alexa, decrease the bedroom fan speed by 3."

Changing mode settings

• "Alexa, set oscillation to wide."

Temperature controls (for Dyson heaters)

• "Alexa, make it warmer in here."
• "Alexa, make it cooler in here."
• "Alexa, turn off the heat."

Alexa learns the more it is used and is always improving its natural voice recognition. Ease of use will improve over time, however some utterances and commands may need to be in a specific format for Alexa to recognise them.

For example, instead of asking "Alexa, turn on oscillation mode.", try asking "Alexa, turn on oscillation.".

This approach can work with other commands as well. Instead of "Alexa, turn on heating mode.", you can ask "Alexa, turn heat on.".

Google and Google Home are trademarks of Google LLC.

Connect your Dyson machine to your Google Assistant-enabled device

Open the Google Home app and tap the plus icon in the top left. Set up a new device and select "Have something already set up?" Search for "Dyson" and tap to select the Dyson Action.

You'll be prompted to link your Dyson account, this is the one you used to connect your machine to the Dyson Link app.

Follow the instructions in the Google Home app to add your Dyson machines.

How does Google Assistant discover my machine?

When you first connect your Dyson machine to the Dyson Link app you'll give it a room name. You'll find a list of pre-set room names in the app, such as 'Bedroom' or 'Kitchen'. Google Assistant uses this room name to identify your machine.

Google Assistant uses this to name your machine in the Google Home app as well.

How do I control an individual Dyson machine?

To control an individual Dyson machine using voice commands, you can either directly name the machine in your command or say the room name the machine is assigned to in the Google Home app.

If you say "Hey Google, enable auto mode in the Bedroom", Google Assistant will identify the machine named 'Bedroom' or a machine in the bedroom and enable auto mode.

Saying "Hey Google, enable auto mode", will enable auto mode for any purifiers in your current room, if the room is set up in the Google Home app.

Disconnecting your machine from the Google Home app

Open the Google Home app and tap the machine you wish to remove.

Tap the settings icon in the top right and select "Unlink Dyson".

When you remove your Dyson machine from a home:

• It will disconnect the device from members in the home
• It will be unlinked from your Google Account
• Data associated with this device will be deleted. Note: Some basic device data may remain associated with the home.

Check for device or setup issues

Your machine must be connected to the Dyson Link app and the Dyson Action must be enabled for Google Assistant to discover your machine.

If your machine hasn't been connected to the Dyson Link app, open the app and select Add machine. Follow the in-app connection instructions.

Check your machine

• Unplug your machine and wait for 10 seconds. Plug your machine back in and turn it on.
• Unplug your smart home device and wait for 10 seconds. Plug it back in.
• Open your Dyson Link app and check that your machine is online.

Check the Dyson Action

• Open the Google Home app and check that the Dyson Action is enabled
• Unlink the Dyson Action and then re-link it

Check Google Assistant can hear you

Google Assistant may not have heard you or recognised your question or command. Make sure you are close enough to your smart home device and speak clearly.

Check Google Assistant can hear you by asking "Hey Google, what did I just say?". Your smart home device should light up when you say "Hey Google ...". If your device has a screen, you'll see it respond.

Check your smart home device

First, make sure:

1. Your Google Nest or Google Home speaker or display is powered on and plugged into a wall outlet
2. The microphone isn't muted
   • For Google Home: on the back of the device, touch the microphone mute button. Your Assistant will say whether the microphone is muted.
   • For Google Nest Mini (2nd gen) and Google Home Mini (1st gen): on the side of the device, toggle the mic switch. Your Assistant will say whether the microphone is muted.
   • For Google Nest Audio: on the back of the device, next to the power cord, toggle the mic switch. Your Assistant will say whether the microphone is muted.
   • For Google Nest displays: on the back of your display, use the switch to turn on the microphone. Your Assistant will say whether the microphone is muted.
3. The LED dots on top of your speaker or display spins or blinks when you say “Ok Google” or "Hey Google."
4. If your Assistant answers other questions, try to ask the unanswered question in a different way.

General troubleshooting

If you've checked off all of the steps above and your Assistant still doesn't provide an answer, try one of the steps below and ask your question again. If you still don't get an answer, move to the next step.

Reboot your speaker or display

1. Disconnect the power cable from your device.
2. Reconnect the power cable.

Make sure your device recognizes the hotword

Say “Hey Google” to your speaker or display. Check if the LED dots on the top of your device spin or blink, indicating that it recognized the hotword.

Make sure your device recognised the question correctly

1. Ask your Assistant the question again.
2. Say "Hey Google, repeat the question" to make sure your Assistant understood you correctly.
3. If it's still not recognizing the question, try to speak slower or try another question.

Resetting your password

If you aren't able to log in to link your Dyson account to the Google Home app, you may need to reset your Dyson account password.

Select the forgotten password link on the log in screen and follow the instructions.

After changing the password on your Dyson account, you'll need to wait 30 minutes before logging back in.

If you enter the password incorrectly more than four times, your account will be locked. It will be automatically unlocked after 30 minutes.

What did Google Assistant hear?

Your command may have been misheard or misinterpreted by Google Assistant. To check this say "Hey Google, show me my activity" to bring up your recent activity, including recent voice commands.

You can also ask Google Assistant to read back the last command by asking "Hey Google, what did you hear?"

What actions did Google Assistant take?

Saying "Hey Google, show me my activity" will show you recent voice commands. You can view the details of each command to see what Google Assistant heard, the responses and actions taken.

What are some of the things I can ask Google Assistant?

There are different commands that can be used to interact with Google Assistant, here are some examples:

Turning your Dyson machine on and off

• "Hey Google, turn on my purifier"
• "Hey Google, turn on night mode"
• "Hey Google, turn off humidification on the purifier"

Changing fan speed

• "Hey Google, set the bedroom fan speed to 7"
• "Hey Google, turn up the bedroom fan speed"
• "Hey Google, decrease the bedroom fan speed by 3"

Changing oscillation settings

• "Hey Google, turn on oscillation mode"
• "Hey Google, set oscillation to wide"

Changing temperature settings

• "Hey Google, make it warmer in here"
• "Hey Google, make it cooler in here"
• "Hey Google, turn off the heat"

Controlling your Dyson robot

• "Hey Google, start vacuuming"
• "Hey Google, stop the vacuum"
• "Hey Google, return the vacuum to the dock"

Google Assistant learns the more you use it but some commands may not be recognised. Try using different words in your command.

For example, if you say "Hey Google, turn on fan motion", and it doesn't work, try saying "Hey Google, turn on oscillation mode".

Please ensure you have the most up to date software downloaded before beginning any checks. We strongly recommended enabling auto-updates in your Dyson Link app settings, to allow the most up to date software to be installed as soon as it is available.

Ensure correct button on remote is being pressed.

On/Off

Airflow speed

Oscillation

Automatic mode

Information

Night mode

Airflow direction

Point the remote directly at the front of the machine while pressing the button.

Check other buttons

Test the other buttons on the remote.

Airflow speed

Airflow direction

Changing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.

Check with the Dyson Link app

Open the app and set the machine to oscillate.

Point the remote at the base of the purifier and test the controls.

Check if the Dyson Link app is working.

Changing the battery

Unscrew the remote control's battery compartment.

Loosen the base and pull it away from the remote. Replace the battery with type CR 2032.

Please ensure you have the most up to date software downloaded before begining any checks. We strongly recommended enabling auto-updates in your Dyson Link app settings, to allow the most up to date software to be installed as soon as it is avaliable.

The first time your purifier is turned on, the gas sensors will perform a self-calibration which takes one hour after which time they will work normally.

If the power cuts out within the hour, the initialisation period will continue from where it left off.

If your machine is new out the box and has not been turned on for over an hour, please allow a full hour to complete, with your purifier plugged into a secure power souce.

Once the full hour has elapsed, turn the machine off and then on again, either with the main power button on the machine, or the remote control.

More than one hour

If your purifier has been plugged into a stable power source for over one hour, and the VOC and/or NO2 screens still do not show, please unplug your machine from the wall, leave for one minute, plug back in, and then turn on using either the main power button, or the button on the remote.

Fault

Reset the machine.

Unplug the machine and leave it for 10 seconds.

Ensure the power cord is plugged into the centre of the base.

Plug the machine back in and retest.

Restart the machine

Switch off and unplug the machine.