Accessibility Statement Skip navigation
Thanks. We've saved your preferences.
You can update your contact preferences at any time in the Keep in touch section of Your Dyson. If you have a Your Dyson account, you can log in below to manage your contact options.

Let's get your machine working.

See all steps

Please select the appropriate option

How to clean the bin and cyclone

Remove the clear bin by holding the machine by the handle and pulling the red lever back, and then lift upwards to release the cyclone.

Press the red Bin release catch located to the rear of the clear Bin.

Remove the clear Bin fully.

Clean the bin with a damp cloth only. Do not use any detergents, polishes or air fresheners to clean the bin. Do not put the bin in the dishwasher.

Clean the cyclone shroud with the brush on the combination tool to remove lint and dust.

Do not immerse the whole cyclone unit in water or pour water into the cyclones.

Ensure the bin is completely dry before replacing. To replace the bin, push it up and in to the Main body of the machine until it clicks in to place.

Close the bin base so it clicks into place and is secure.

Is there anything else we can help you with?

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Please select the appropriate option

Assembling your Dyson machine

Attach the Wand to the machine via the bin inlet.

Attach the floor tool to the end of the Wand until it clicks.

Is there anything else we can help you with?

Installing the wall dock

Please note that wall fixings are not included with the dock.

Feed the charger cable through the rear of the dock, ensuring it is held via the retainer clip as shown in the image.

Clip the end of the charger cable in the small bracket located to the front of the dock assembly until it clicks.

When securing the dock to the wall, ensure there is a distance of 1200m/47¼” from the floor. This is to allow the machine to sit in the dock without touching the floor.

Is there anything else we can help you with?

How to attach the accessories

All the tools provided with the machine fit directly to the Wand or the bin inlet.

Image showing how to assemble your machine.

Click the tools to the end of the Wand, ensuring the connections line up.

Remove the Wand. Place the tools directly onto the bin inlet until they click.

Is there anything else we can help you with?

User guide

Please see the attached user guide above.

Is there anything else we can help you with?

Getting started

Please follow the steps in the video.

Is there anything else we can help you with?

Finding the serial number

The serial number can be found underneath the machine on the battery.

Image showing how to find the serial number of your machine.

Is there anything else we can help you with?

High pitch whistle

A high pitch whistle could indicate a seal is damaged or the machine is blocked.

Please follow the performance route.

Please select the appropriate option

Check the sound

Remove all tools and accessories from the machine.

Image showing how to remove the cleaner head from your machine.

Put the machine in max power mode by sliding the switch towards max.

Image showing how to change the power mode of your machine.

Pull and hold the trigger for 10 seconds.

Image showing to pull the power trigger.

Does the machine pulsate and cut out without any tools?

Check the bin inlet

With the bin removed, check the bin inlet flap for blockages and remove as necessary.

Ensure that it moves freely.

Fluff or fibers jamming the hinge can cause the flap to close resulting in low suction and a pulsating noise.

Close the bin base - hold the bin so that the inlet is pointing to the floor and shake the bin.

Does the bin rattle?

Check the cyclone

Clean shroud using the brush part of the combination tool.

Clear the center of the cyclone of any dirt or debris.

Check that the seals are not missing or damaged:

FDC seal between the cyclone and the bin base.

Seal between the cyclone and the top of the clear bin.

Seal around the bin base.

Re-assemble and test the machine.

Has checking the cyclone and seals solved the problem?

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

We need a little more information to help us solve your issue.

Please call our customer service team on 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Checking the wand

Remove the wand from the bin inlet.

Image showing how to remove the wand from your machine.

Check both ends of the wand for blockages and remove as necessary.

Re-assemble and test the machine.

Has checking the wand resolved the problem?

Ensure the appliance is disconnected from the charger before removing the filter. Be careful not to pull the 'ON' trigger.

Remove the filter

To remove the filter, lift it out of the top of the machine.

Washing the filter

With cold water only, run water over the outside of the filter until the water runs clear.

Turn the filter upside down and shake to remove any excess debris.

Squeeze and twist the filter with both hands to make sure the excess water is removed.

Image showing how to wash the filter.

Lay the filters on its side, and leave it to dry completely for a minimum of 24 hours.

WARNING: Do not put the filter in a dishwasher, washing machine, tumble dryer, over, microwave, or near a naked flame.

Image showing DO NOT refit the filter until dry.

Replacing the filter

To re-fit the filter, place the dry filter back into the top of the machine. Ensure it is fitted properly.

Has washing the filter resolved the issue?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Remove the bin and turn on the machine.

Pull the cyclone release catch upwards until the bin base opens.

Push the cyclone back down, leaving the bin base open.

Press and hold the trigger for 10 seconds.

Please note the machine will only run with the cyclone on and pushed down.

Does the machine pulsate with the bin open?

Remove the filter

Pull the filter out of the top of the cyclone.

Image showing how to remove the pre-filter from your machine.

Press and hold the trigger for 10 seconds.

Image showing to pull the power trigger.

Does the machine pulsate with the filter removed?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the sound

Remove all tools and accessories from the machine.

Image showing how to remove the cleaner head from your machine.

Put the machine in max power mode by sliding the switch towards max.

Pull and hold the trigger for 10 seconds.

Does the machine pulsate and cut out without any tools?

Check the mini motorized head

Put the mini motorized head on the machine.

Press and hold the trigger for 10 seconds.

Image showing to pull the power trigger with the mini motor head attached.

Does the machine pulsate and cut out with the Mini motorized head?

Test the floor tool

Attach the main floor tool directly onto the bin inlet (without the wand).

The floor tool shown may vary from the product selected but the process remains the same.

Image showing how to attach the cleaner head to your machine.

Press and hold trigger for 10 seconds.

Does the machine pulsate and cut out with the floor tool attached?

Clear the floor tool

With the floor tool removed from the machine, remove the lower soleplate and undo one fastener.

Remove brushbar and clear away any hair or fibers.

Check the openings for any blockages and remove as necessary.

Re-fit the brushbar, ensuring that no bristles get stuck in either end.

Has clearing the floor tool resolved the problem?

Check the bin inlet

With the bin removed, check the bin inlet flap for blockages and remove as necessary.

Ensure that it moves freely. Fluff or fibers jamming the hinge can cause the flap to close resulting in low suction and a pulsating noise.

Close the bin base - hold the bin so that the inlet is pointing to the floor and shake the bin.

Does the bin rattle?

Clear the bin inlet flap

This indicates that the bin entry inlet is jammed.

Re-check the flap, push it open by hand a few times until it is free.

Can the flap be pushed open by hand?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clear the floor tool

With the floor tool removed from the machine, turn over and undo the fastener.

Rotate the end cap to unlock and remove.

Remove the brushbar and clear away any hair or debris.

Pull end cap away from the brushbar, clean and re-connect.

Check the openings for any blockages, remove as necessary and replace the brushbar.

Use a coin to lock the fastener, then re-assemble and test the machine.

Has checking the floor tool resolved the issue?

Check the bin inlet

Pull the red lever located on the top of the machine upwards until the bin flap is open.

Press the red bin release lever, located to the rear of the clear bin.

Check the bin inlet ensuring that it moves freely. Fluff or fibers jamming the hinge can cause the flap to close resulting in low suction and a pulsating noise.

Does the bin rattle?

Clear the mini motorized head

With the tool removed from the machine, unlock the endcap using a coin.

Image showing how to unlock the mini brush bar.

Check the opening for blockages and remove as necessary.

Refit the brushbar ensuring that no bristles get stuck in either end, then re-assemble and test the machine.

Has clearing the Mini motorized head resolved the problem?

Check the floor tool

Remove all tools and accessories from the machine.

Image showing how to remove the cleaner head from your machine.

Put the machine in max power mode.

Pull and hold the trigger for 10 seconds.

Is the noise still present?

Test without the bin

Pull the cyclone release catch upwards until the bin base opens.

Press the red catch once the bin base is open to release the bin assembly.

Push the cyclone down to click into place.

Image showing how to close down the cyclone without the bin attached.

Press and hold the trigger for 10 seconds.

Please note the machine will only run with the cyclone on and pushed down.

Image shows to pull the power trigger.

Refit the bin

Pull the cyclone release catch upwards until the bin base opens.

Image showing how to pull up the cyclone.

To re-fit, locate the tabs at the back of the bin in the main body, then push the bin up until it locks in place and the power connectors are fitted together.

Is the noise still present without the bin?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check the floor tool

Remove all tools and accessories from the machine.

Image showing how to remove the cleaner head from your machine.

Put the machine in max power mode.

Pull and hold the trigger for 10 seconds.

Does the machine still making a grinding noise?

Please select the appropriate option.

Has any part of the machine been washed?

Wash the filter

Please follow the steps in the video.

Has washing the filter resolved the issue?

Machine pick up

Under normal use, any unpleasant smell can only be caused by something the machine has picked up.

We would advise you to carry out the blockage checks.

Please select the appropriate option

Does the machine pulsate and cut out without any tools?

Ensure the appliance is disconnected from the charger before removing the filter. Be careful not to pull the 'ON' trigger.

Washing the filter

To remove the filter, lift it out of the top of the machine.

Image showing how to remove the pre-filter from your machine.

With cold water only, run water over the outside of the filter until the water runs clear.

Turn the filter upside down and shake to remove any excess debris.

Squeeze and twist the pre-filter with both hands to make sure the excess water is removed.

Image showing how to wash the filter.

Lay the filter on their side, and leave them to dry completely for a minimum of 24 hours.

WARNING: Do not put the filters in a dishwasher, washing machine, tumble dryer, over, microwave, or near a naked flame.

Image showing guidelines on how to dry the pre-filter.

To re-fit the filter, place the dry filter back into the top of the machine. Ensure it is fitted properly.

Has washing the filter resolved the issue?

Washing the machine

Only the filter can be washed, the bin can be cleaned with a damp cloth only, and both must be completely dry before being re-fitted to the machine.

Were all the washed parts completely dry before the machine was used?

Machine pick up

Under normal use, any unpleasant smell can only be caused by something the machine has picked up.

Please see the pick-up route on how to remove a blockage.

Please select the appropriate option

We need a little more information to help us solve your issue.

Please call our customer service team on 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Select floor tool

Which floor tool is currently not working correctly?

Test the power

Remove the machine from the charger and ensure the machine is fully assembled.

Pull the power trigger.

Image shows to pull the power trigger.

Does the machine have power?

Clear the floor tool

With the floor tool removed from the machine, remove the lower soleplate.

Undo one fastener to remove.

Remove brushbar and clear away any hair or fibers.

Check the openings for any blockages and remove as necessary.

Re-fit the brushbar ensuring that no bristles get stuck in either end.

Re-assemble and test the machine.

Is the brushbar now spinning constantly?

Test the wand

Remove the tool from the wand.

Remove the wand from the machine.

Image showing how to remove the wand from your machine.

Put the tool directly onto the machine and test without putting the tool in contact with any surface.

Image showing how to attach the cleaner head to your machine.

Does the brushbar spin when the head is attached to the bin inlet?

Check the bin inlet

Check the bin inlet connections to ensure that they are not bent or damaged.

Has checking the electrical contacts resolved the problem?

Is this surface a long pile carpet or rug?

Try on short-pile carpet

Try the tool on a low pile carpet.

Does the brushbar spin while in contact with the short-pile carpet?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Test the floor tool

Test the floor tool on a surface where it has previously stalled.

Does the brushbar spin while in contact with the floor?

Is this surface a long pile carpet or rug?

Try on short-pile carpet

Try the tool on a low pile carpet.

Does the brushbar spin while in contact with the short-pile carpet?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Red flashing light on machine.

Pull the trigger and count the number of red flashes.

Image shows red flashing light on top of the power pack.

How many times did the light flash?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Reset

Press the button for 3 seconds and release.

Image showing to pull the power trigger.

Repeat this 5 times.

Is there still an amber light?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Charge the machine

Put the machine on charge for 3.5 hours and test it again.

Has this resolved the issue?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Charge machine

A solid blue light will show when the machine is being charged and will go out when charging is complete.

Please charge the battery for 3.5 hours before contacting customer services.

Has this resolved the problem?

We need a little more information to help us solve your issue.

Please call our customer service team on 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Check for blockages

If the blue light is solid but the machine is cutting out please check your machine for a blockage somewhere in the machine.

Image showing solid blue light on top of the power pack.

Check the sound

Remove all tools and accessories from the machine.

Image showing how to remove the cleaner head from your machine.

Put the machine in max power mode by sliding the switch towards max.

Image showing how to change the power mode of your machine.

Pull and hold the trigger for 10 seconds.

Image showing to pull the power trigger.

Does the machine pulsate and cut out without any tools?

Return to working temperature

This indicates that the machine is outside of it's normal operating temperature (5oc - 35oc).

Please place the machine in an area that stays within this temperature range and leave it to charge there for 3.5 hours.

Image showing flashing amber light on top of the power pack.

Has this resolved the problem?

We need a little more information to help us solve your issue.

Please call our customer service team on 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Test the power

Remove machine from the charge, and ensure the machine is fully assembled.

Pull the power trigger.

Image shows to pull the power trigger.

Does the machine have power?

Test the power

Remove the machine from the charger and ensure it's fully assembled.

Image showing how to remove the charger from your machine.

Pull the power trigger.

Image shows to pull the power trigger.

Does the machine have power?

Clear the floor tool

With the floor tool removed from the machine, turn over and undo the fastener.

Rotate the end cap to unlock and remove.

Remove the brushbar and clear away any hair or debris.

Pull end cap away from the brushbar, then clean and reconnect.

Check the openings for any blockages and remove as necessary. Replace the brushbar.

Use a coin to lock the brushbar.

Is the brushbar spinning constantly?

Retry the floor tool

Test the floor tool on a surface where it has previously stalled.

Does the brushbar spin while in contact with the floor?

Is this surface a long pile carpet or rug?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Amber light while charging

If the machine was in Max power mode when it ran out of battery, an amber light may show while it is charging.

This is normal and the light will go off before the end of the charge. Please leave the machine for 3.5 hours to recharge fully.

Please select the appropriate option

We need a little more information to help us solve your issue.

Please call our customer service team on 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Does the machine have power?

Clear the mini motorized head

With it removed from the machine, remove the brushbar from the mini motorized head.

Using scissors carefully cut any hair or fibers away from the brushbar.

Re-assemble the tool and attach it to the machine.

Test the tool without putting it in contact with any surface.

Does the brushbar still not work properly without any contact?

Check the bin inlet

Check the bin inlet connections to ensure that they are not bent or damaged.

Has checking the connection resolved the issue?

Check the floor tool

Place the main floor tool on directly on to the machine.

Image showing how to attach the cleaner head to your machine.

Do other tools work on the machine?

Clear the mini motorized head

With the tool removed from the machine, undo fastener.

Remove brushbar and clear away any hair or fibers.

Refit the brushbar ensuring that no bristles get stuck in either end.

Has cleaning the tool resolved the issue?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Removing the battery

There are 3 phillips screws that need to be removed, prior to removing the battery.

Remove the post-filter, then using a small phillips screwdriver unscrew the screw located on the rear of the main body.

Place the main body on its side on a flat surface, and locate the two screws near the battery.

Unscrew the screws and gently pull the battery away from the main body assembly.

Has this resolved the issue?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Removing the cyclone

Lift the red lever on top of the cyclone assembly fully.

Press the red lever located to the rear of the bin assembly to fully remove the bin.

Behind the cyclone assembly on the main body of the machine are two cyclone release buttons.

Press either side and gently pull the cyclone upwards.

Has this resolved the issue?

Check the catch and tools

Check the catch on the bin inlet for blockages or damage.

Make sure that it moves freely and springs back into position when pressed.

Check the end of the wand for signs of damage.

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Talc

This is normal. Talc was used in Production for the fitting of seals.

Further application of talc will not be required.

Sealed products are brand new and have not been resold as conditioned machines.

Is there anything else we can help you with?

Check the bin inlet

The flap can become jammed by a build up of dirt and debris.

Open the bin base by lifting the lever on top of the cyclone assembly.

Press the red bin release catch located to the rear of the clear bin to remove the bin fully.

Clear any debris from behind the bin inlet flap.

Re-assemble and test the machine.

Has this resolved the problem?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Marks on the wand

Marks on the wand can be caused when it has come into contact with a painted surface such as a door frame.

These can be removed by wiping with a damp cloth (Do not use any cleaning chemicals or solvents).

Has this resolved the problem?

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Please select the appropriate option

Machine runtime

Powerful suction mode (motorized head and mini motorized head) – 20 minutes run time.

Powerful suction mode (with Combination tool and crevice tool) - 30 minutes run time.

Image showing how to change the power setting for the tools.

Max mode - 6 minutes with all tools.

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Unplug machine from charger

Make sure the machine is unplugged from the charger.

Does the machine currently have power?

Unplug machine from charger

Please ensure the machine is unplugged from the charger.

Apologies. We can’t help you online.

Our Customer Support Team will be able to solve your problem at 1-866-314-8881.

For Supersonic™ hair dryer Professional edition owners, please contact us at 1-866-861-2565.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

How to charge the battery

The machine can be charged on the dock or by plugging the charger directly to the machine.

The light on the charger will show when the machine is being charged and will go out when charging is complete.

The battery should be fully charged after 3.5 hours.

Is there anything else we can help you with?

Clear the floor tool

Under the Cleaner head by the Soft roller, locate the fastener. Using a coin, turn the fastener anticlockwise a quarter of the way to remove the end cap.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

Please select the appropriate option

Washing the Brush bar

Beware of sharp objects when checking for blockages.

Turn the Cleaner head upside down so the underside of the Cleaner head is facing you.

Rotate the end cap to the open position.

Rotate the end cap to unlock and remove.

Gently slide the large Brush bar away from the Cleaner head and remove the end cap from the Brush bar.

Image showing how to reconnect the end cap to the soft roller.

Lift the smaller Brush bar up to remove.

Wash both the large and small Brush bar until the water runs clear.

Image showing how to wash the soft roller brush bar.

Stand both Brush bars upright, leave to dry completely for a minimum of 24 hours.

Image showing recommended guide to drying your soft roller.

Refit the small Brush bar first by inserting the round end of the small Brush bar into place. Push down the octagonal end until it clicks into place.

Image showing how to reassemble the soft roller brush bar.

Reattach the end cap to the large Brush bar.

Slide the large Brush bar back onto the Cleaner head around the motor. Once in place rotate the end cap back into the closed position.

Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is fully turned and that both the base plate and Brush bar is secure.

Is there anything else we can help you with?

We're glad the problem's been solved.

Please let us know if there's anything else we can help you with.

How would you rate our online support?

1/5 Poor

2/5 Average

3/5 Good

4/5 Very Good

5/5 Excellent

Clean the floor tool

Undo one fastener to remove the Brush bar.

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

Is there anything else we can help you with?

Clear the floor tool

On the side of the Cleaner head, locate the end cap. Using a coin, turn the end cap anticlockwise a quarter of the way to remove it.

Note: There should be a small padlock icon along with directional arrows to help you unlock the end cap.

Remove the Brush bar from the Cleaner head and clear away any hair or fibres.

Check the neck of the Cleaner head (where the Cleaner head connects to the Wand) for any blockages. Ensure there is no build up of dust or debris in the small crevice between where the Brush bar sits and the neck of the Cleaner head.

With the Brush bar clear from any debris, refit it back into the Cleaner head and securely fasten the end cap.

Place the Cleaner head onto the bin and test the machine.

Is there anything else we can help you with?

Empty the bin

Empty as soon as the dirt reaches the level of the MAX mark - do not overfill. Ensure the machine is disconnected from the charger before emptying the clear bin. Be careful not to pull the 'ON' trigger.

Image showing how to remove the charger from your machine.

To release the dirt, hold the appliance by the handle, pull the red lever back and lift upwards.

Continue until the bin base automatically opens and releases the dirt.

Once the dirt is released, push the cyclone back down until it clicks.

Close the bin base of the machine ensuring it clicks in to place.

To close, push the cyclone downwards until it is in the normal position and manually close the base of the bin. The base will click when it is securely in place.

Is there anything else we can help you with?

Washing the filter

To remove the filter, lift it out of the top of the machine.

With cold water only, run water over the outside of the filter until the water runs clear.

Turn the filter upside down and shake to remove any excess debris.

Squeeze and twist the filter with both hands to make sure the excess water is removed.

Drying the filter

Lay the filter on its side to dry. Leave to dry completely for a minimum of 24 hours.

Do not put the filter in a dishwasher, washing machine, tumble dryer, oven, microwave or near a naked flame.

Image showing guidelines on how to dry the pre-filter.

Replacing the filter

To refit the filter, place the dry filter back into the top of the machine. Ensure it is fitted properly.

Is there anything else we can help you with?